Set-Up & First Brew
IMPORTANT:You cannot use your Keurig
brewer until it has been primed for its first use
as set forth below.
Priming your Brewer
1. Unwrap cord and plug the brewer into a
grounded outlet.
2. Place a cup or mug on the Drip Tray Plate.
3. Remove the Water Reservoir from Brewer by
first removing Lid from Reservoir, then lifting
Reservoir straight up and away from Brewer
(may be tight). Rinse with fresh water.
4. Fill Water Reservoir with fresh water so that
the water level is just below the top edge of
the reservoir.
5. Place Water Reservoir base into the left
side of the Brewer and be sure the
Water Reservoir Lock Tabs engage
with the Brewer. Replace Lid on Water
Reservoir.
6. Press the Power Button found directly
above the LCD Control Center. The blue light
surrounding the Travel Mug Button will
become illuminated and flash.
7. The LCD Control Center will come on and
indicate 'PRIME' and the button for the
Travel Mug will also flash. Please note, a K-
Cup should not be used for the Priming
Sequence.
8. Press the Travel Mug Button.
9. The Brewer will automatically fill with water
(priming it) and then the water will be
heated. This will take about 3 minutes. During
the heating period 'NOT READY' is dis-
played on the LCD Control Center. Once the
water is heated, 'READY' will be displayed and
the Travel Mug button will flash.
10.Press the Travel Mug Button to start a
cleansing brew, during which hot water will
flow into your cup or mug. Pour the hot
water into the sink.
11.The one-time priming process is now
complete and you are ready to brew!
67
Ready to Brew your First Cup
1. LCD Control Center will indicate 'READY TO
BREW'.
2. Place a cup or mug on the Drip Tray Plate.
3. Lift the Handle and the K-Cup Holder will
open toward you.
4. Select a K-Cup®portion pack.
5. Place a K-Cup®portion pack in the K-Cup
Holder (as shown in exhibit at top of page).
6. Lower the Handle to close the Lid over the
K-Cup Holder. (When it is closed completely,
the LCD Control Center will indicate ‘READY
TO BREW’ and the Cup, Mug and Travel Mug
Buttons will blink up to 60 seconds.)
7. Choose the amount of coffee or tea you
wish to brew by pressing the button that
indicates your choice. The Travel Mugchoice
will yield a 9.25 oz serving, the Mug choice
will yield a 7.25 oz serving and the Cup
choice will yield a 5.25 oz serving.
8. The LCD Control Center will now display the
word ‘BREWING’ and the serving size you
selected will be solid blue.
9. There may be a short pause before the
brewing process begins. The process lasts
for approximately 40 seconds and ends
with a burst of air to remove all liquid
coffee or tea from the K-Cup.
10. Lift the Handle and remove and dispose of
the used K-Cup.
CAUTION: K-Cup will be hot.
11. Enjoy your first cup of Keurig Brewed®
gourmet coffee or tea!
12. Your Brewer may display ‘NOT READY’ as
it heats water for the next brew cycle. The
‘READY TO BREW’ indication will return to
the LCD Control Center in about 15 seconds.
NOTE: You may see small amounts of water
coming from the Vent and dripping into the
Water Reservoir during this and subsequent
heating – this is normal.
NOTE: Do not remove the foil lid or
puncture the K-Cup®portion pack.
NOTE: If the Water Reservoir is empty or
not in place on the Brewer, then the LCD
Control Center will also indicate ‘ADD
WATER’. None of the buttons will be activated
until water is added to the Water Reservoir.
CAUTION: There are two sharp needles that
puncture the K-Cup®portion pack, one above
the K-Cup Holder and the other in the bottom
of the K-Cup Holder. To avoid risk of injury,
do not put your fingers in the K-Cup Chamber.
NOTE: If you do not push the Brew Buttons
in 60 seconds, the LCD Control Center will
return to 'READY TO BREW' and the Brew
Buttons will be disabled to prevent accidental
activation. Re-activate the Brew Buttons by
raising and lowering the Handle completely.
CAUTION: There is extremely hot water in
the K-Cup Holder during the brew process.
To avoid risk of injury, do not lift the
Handle or open the K-Cup Chamber
during the brew process.