8. Maintenance

8. Maintenance

alarms will not be tested and will not alarm. However, when pressing the Test button on an interconnected smoke alarm, the CO alarm will emit a Smoke/Fire audible and visual alarm pattern of 3 long beeps, 1 second of silence, repeated. NOTE: You do not need to press the Test button to take a CO reading.

Battery Replacement (for alarms with battery backup)

These CO alarms are not battery operated. However, these alarms are equipped with 9 volt battery backup – the 9 volt battery is to supply short term back-up during a power outage.

When replacing the battery, use one of the following approved brands:

• Duracell

MN1604 or MX1604

• Energizer

522

These batteries can be purchased where you bought the alarm or at a local hardware store. Use of a different battery may have a detrimental effect on the alarm operation.

The 9 volt battery is not rechargeable. If the 9 volt battery is missing, disconnected, or if the battery’s power is low, a red LED flash will occur once every 15 seconds, accompanied by an audible beep. If this

CAUTION!: If the battery tab is not held down in the battery compartment by the battery, the battery door will not close, the AC Quick-Connector will not attach to the alarm, and the alarm will not attach to the mounting plate.

After installing or changing the battery, reinstall your alarm. Test your alarm by using the Test/Reset button and check that the green “Power” LED is on.

Maintenance Tips

To keep your alarm in good working order, you must follow these simple steps:

Test the alarm once a week by pressing the Test/Reset button.

Vacuum the alarm cover once a month to remove accumulated dust.

Battery Tab

Battery Replacement

happens, the battery must be replaced. (For model KN-COP-IC with digital display: “Lb” will be displayed alternately with the current CO reading once every second).

IMPORTANT: Constant exposures to high or low humidity may reduce battery life. A good safety measure is to replace the battery at least once a year, or at the same time as you change your clocks for daylight saving time.

Alarm Removal

If the tamper resist feature has been activated, refer to tamper resist feature description in section 4 for removal instructions.

Remove the alarm from the mounting plate by rotating the alarm in the direction of the “OFF” arrow on the cover. To disconnect the AC Quick- Connector harness, squeeze the locking arms on the sides while pulling the connector away from the bottom of the alarm (see section 4).

After the alarm has been removed, you can open the battery door and replace the battery. Battery installation instructions are provided on the inside of the battery door.

When installing the battery, orient the battery as shown on unit label. Press the battery tab down into the battery compartment and install the battery.

Never use detergents or solvents to clean the alarm. Chemicals can permanently damage or temporarily contaminate the sensor.

Avoid spraying air fresheners, hair spray, paint or other aerosols near the alarm.

Do not paint the unit. Paint will seal the vents and interfere with proper sensor operation.

Move the CO Alarm to a remote location, to prevent possible damage or contamination of the sensor, prior to performing any of the following:

Staining or stripping floors or furniture, painting or wall-papering

Using aerosols or adhesives

WARNING: Reinstall the CO Alarm as soon as possible to assure contin- uous protection.

The following is a list of substances that at high levels can damage the sensor or cause temporary readings that are not CO readings:

Ethylene, ethanol, alcohol, iso-propanol, benzene, toluene, ethyl acetate, hydrogen, hydrogen sulfide and sulfur dioxide.

Also most aerosol sprays, alcohol based products, paint, thinner, sol- vent, adhesive, hair spray, after shave, perfume, auto exhaust (cold start) and some cleaning agents.

Page 11
Image 11
Kidde kn-cobic Battery Replacement for alarms with battery backup, Duracell MN1604 or MX1604 Energizer 522, Alarm Removal

kn-cop-ic, kn-cobic specifications

The Kidde KN-COP-IC and KN-COB-IC are advanced carbon monoxide (CO) and explosive gas detectors designed to enhance home safety through state-of-the-art technology. These devices serve as a crucial line of defense against the dangers posed by carbon monoxide, a colorless, odorless gas that can lead to serious health risks or even fatality if undetected.

One of the main features of the Kidde KN-COP-IC is its electrochemical CO sensor, which provides accurate readings while also minimizing the chances of false alarms. This sensor technology allows the device to detect the presence of carbon monoxide at lower concentrations, making it effective in a variety of environments, including homes, garages, and other enclosed spaces. The KN-COB-IC model, focusing on explosive gases, utilizes a sophisticated catalytic bead sensor that can precisely identify the presence of combustible gases, such as natural gas and propane.

Both models are equipped with a digital display that provides real-time readings, making it easy for users to monitor CO levels and other hazardous gases present in their environment. The KN-COP-IC offers a peak level memory feature, which stores the highest levels of CO detected since the last reset. This helps users understand previous exposure levels, potentially informing safety and health decisions.

In terms of installation and usability, the Kidde detectors come with a battery backup to ensure continuous operation, even during power outages. They are designed for easy mounting, whether on walls or ceilings, and are compact enough to blend seamlessly into home decor. Furthermore, the integrated test/silence button allows users to check the functionality of the alarm and silence it during false alarms or maintenance checks.

Both the KN-COP-IC and KN-COB-IC models meet stringent safety standards and certifications, ensuring they provide reliable protection. Regular maintenance is simplified with clear instructions included in the user manual, along with the recommendation to replace the units after a specified period, usually around 7 years for CO detectors.

In conclusion, the Kidde KN-COP-IC and KN-COB-IC are essential tools in modern home safety. With their advanced sensor technology, user-friendly features, and reliable performance, these detectors not only safeguard families from carbon monoxide and explosive gases but also promote peace of mind in everyday living. By investing in these reliable detectors, homeowners can ensure the safety and well-being of their loved ones.