Manuals / Kingston Technology / Computer Equipment / Switch

Kingston Technology KNE8TX/WG manual Hardware Installation, Front Panel, Power LED

Models: KNE8TX/WG

1 27

Download 27 pages 36.68 Kb

Page 10

Hardware Installation

4	Front Panel

Hardware Installation

Before you begin installing network cables, please take a few moments to familiarize yourself with the EtheRx hubs. The front and rear panels of the Fast Ethernet Workgroup hubs are illustrated below.

Front Panel

PWR

KNE4TX/WG

Utilization LEDs				UTP Port LEDs
I 0 0 B A S E - T X	C l a s s		Repeater	EtheRx Workgroup
UTIL %				LINK / ACTIVITY / PARTITION
1 12 25 50	60	C O L L		1 2 3 4	CASCADE

Power LED

Collision LED

Cascade Switch

Fig. 1-2 KNE4TX/WG Front Panel

PWR

KNE8TX/WG

Utilization LEDs			UTP Port LEDs
I 0 0 B A S E - T X	C l a s s		Repeater	EtheRx Workgroup
UTIL %			LINK / ACTIVITY / PARTITION
1 12 25 50	60	COLL	1 2 3 4 5 6 7	8	CASCADE

Power LED

Collision LED

Cascade Switch

Fig. 1-3 KNE8TX/WG Front Panel

Power LED

The green LED indicates the power status. The LED will light up when the unit is properly connected to the accompanying DC power supply. For further details, please refer to Figure 1-8on page 8.

Kingston Technology Company

KNExTX/WG User’s Guide - Rev. A00

Image 10

Kingston Technology manual Hardware Installation, Power LED, 2 KNE4TX/WG Front Panel, 3 KNE8TX/WG Front Panel

Contents

KINGSTON TECHNOLOGY MODELS KNE4TX/WG KNE8TX/WGPage Part No. 4460057-001.A00 Kingston Technology’s EtheRx Workgroup 4-Port and 8-Port100BASE-TX Fast Ethernet Hubs User’s Guide Kingston Technology Company 17600 Newhope Fountain Valley, CA 714Special Features TABLE OF CONTENTSPackage Contents Error-HandlingAppendix B Page Model Types IntroductionFig. 1-1 - KNE4TX/WG & KNE8TX/WG Special Features Package ContentsRepeater Functions Design FeaturesError-Handling Receive Jabber ProtectionFront Panel Hardware InstallationPower LED Fig. 1-2 KNE4TX/WG Front PanelCollision LED Utilization LEDs4 or 8 UTP Port LEDs Notes on MDI and MDI-X Ports Cascade SwitchFig. 1-4 Cascade Switch functions Using a Straight-Through CableFig. 1-5 - Typical Class II Repeater Cascade Configuration Table 1-1 Cascade Switch functionsRear Panel DC Power ConnectorFig. 1-8 DC Power Connector 4 or 8 UTP PortsKNExTX/WG User’s Guide - Rev. A00 AppendicesAppendices Kingston Technology CompanyUTP Pin Assignments Fig. A-1 RJ-45 Connector Pin NumbersAppendix A Pin Assignments Table A-1 UTP Pin AssignmentsStraight-Through Cable Wiring UTP Cable WiringCable Wiring Standards Crossover” Cable WiringFig. B-2 4-Pair T568B Wiring Fig. B-1 4-Pair T568A WiringTable B-3 4-Pair T568A Wiring Table B-4 4-Pair T568B WiringRating Codes Terms You Should Be Familiar WithEtheRx 4- and 8-Port Fast Ethernet Workgroup Hubs SpecificationsAppendix C EnvironmentalFCC Class A, CE CISPR A Appendix D Commonly Asked QuestionsEMI Standards EMC StandardsClass I vs. Class II 100BASE-TX Fast Ethernet Repeaters What is Category 5?Appendix D Commonly Asked Questions Will 100BASE-TX run on Category 3 cable?What are the Guidelines for Proper Termination? Appendix E Mounting TemplatesCategory 5 Compliance vs. Category 5 Performance? Can I mix CAT 3 and CAT 5 cabling in the same building?Kingston Technology Company Fig. E-1 Mounting Template specificationsAppendix D Mounting Templates KNExTX/WG User’s Guide - Rev. A00Duration of Warranty Limited Warranty StatementAppendix F Warranties and Notices Disclaimers Warranty Claim RequirementsFree Technical Support Rev. 10/97F.C.C. Certification CE Notice