Manuals / Kingston Technology / Computer Equipment / Switch

Kingston Technology KNE8TX/WG manual F.C.C. Certification, CE Notice

Models: KNE8TX/WG

1 27

Download 27 pages 36.68 Kb

Page 27

Appendix F Warranties and Notices

19

F.C.C. Certification

This device has been tested and found to comply with limits for Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received; including interference that may cause undesired operation.

CE Notice

The official CE symbol indicates compliance of this Kingston Technology product to the EMC directive of the European Community. The CE symbol found here or elsewhere indicates that this Kingston product meets or exceeds the following standards:

❑EN50081-1“Electromagnetic Compatibility-generic emissions standard”

EN55022: “Limits and methods of measurement of radio interference characteristics.”

❑EN50082-1“Electromagnetic Compatibility-generic immunity standard”

IEC 801-2:“Electrostatic discharge requirements”

IEC 801-3:“Radiated immunity requirements”

IEC 801-4:“Electrical fast transient requirements”

❑EN60950 “Low Voltage Directive (LVD)”

❑Declaration of CE Conformity in accordance with the above standards has been made and is on file at Kingston Technology.

KNExTX/WG User’s Guide - Rev. A00

Kingston Technology Company

Image 27

Kingston Technology KNE8TX/WG manual F.C.C. Certification, CE Notice

Contents

MODELS KNE4TX/WG KNE8TX/WG KINGSTON TECHNOLOGYPage Kingston Technology Company 17600 Newhope Fountain Valley, CA 714 Kingston Technology’s EtheRx Workgroup 4-Port and 8-Port100BASE-TX Fast Ethernet Hubs User’s Guide Part No. 4460057-001.A00Error-Handling TABLE OF CONTENTSPackage Contents Special FeaturesAppendix B Page Introduction Model TypesFig. 1-1 - KNE4TX/WG & KNE8TX/WG Package Contents Special FeaturesReceive Jabber Protection Design FeaturesError-Handling Repeater FunctionsFig. 1-2 KNE4TX/WG Front Panel Hardware InstallationPower LED Front PanelUtilization LEDs Collision LED4 or 8 UTP Port LEDs Using a Straight-Through Cable Cascade SwitchFig. 1-4 Cascade Switch functions Notes on MDI and MDI-X PortsTable 1-1 Cascade Switch functions Fig. 1-5 - Typical Class II Repeater Cascade Configuration4 or 8 UTP Ports DC Power ConnectorFig. 1-8 DC Power Connector Rear PanelKingston Technology Company AppendicesAppendices KNExTX/WG User’s Guide - Rev. A00Table A-1 UTP Pin Assignments Fig. A-1 RJ-45 Connector Pin NumbersAppendix A Pin Assignments UTP Pin AssignmentsCrossover” Cable Wiring UTP Cable WiringCable Wiring Standards Straight-Through Cable WiringTable B-4 4-Pair T568B Wiring Fig. B-1 4-Pair T568A WiringTable B-3 4-Pair T568A Wiring Fig. B-2 4-Pair T568B WiringTerms You Should Be Familiar With Rating CodesEnvironmental SpecificationsAppendix C EtheRx 4- and 8-Port Fast Ethernet Workgroup HubsEMC Standards Appendix D Commonly Asked QuestionsEMI Standards FCC Class A, CE CISPR AWill 100BASE-TX run on Category 3 cable? What is Category 5?Appendix D Commonly Asked Questions Class I vs. Class II 100BASE-TX Fast Ethernet RepeatersCan I mix CAT 3 and CAT 5 cabling in the same building? Appendix E Mounting TemplatesCategory 5 Compliance vs. Category 5 Performance? What are the Guidelines for Proper Termination?KNExTX/WG User’s Guide - Rev. A00 Fig. E-1 Mounting Template specificationsAppendix D Mounting Templates Kingston Technology CompanyLimited Warranty Statement Duration of WarrantyAppendix F Warranties and Notices Rev. 10/97 Warranty Claim RequirementsFree Technical Support DisclaimersCE Notice F.C.C. Certification