KitchenAid 2221514A Assistance or Service, Replace Base Grille, Complete Installation

Leveling Refrigerator

The roller adjusting bolts are located behind the base grille. The refrigerator has 4 adjustable rollers (two front and two rear). There are 2 sets of roller adjusting bolts found at the base of the refrigerator on each side.

1.Rear Leveling Bolt (yellow)

2.Front Leveling Bolt (silver)

NOTE: The yellow bolt will adjust the rear of the refrigerator, and the silver bolt will adjust the front of the refrigerator.

1.Use a ¹⁄₂ in. (12.70 mm) socket wrench to adjust the leveling bolts. Turn the leveling bolt to the right to raise that side of the refrigerator or turn the leveling bolt to the left to lower that side. It may take several turns of the leveling bolts to adjust the tilt of the refrigerator.

NOTE: Be careful not to unscrew the leveling bolts too much when lowering the refrigerator. The bolt head will start to come away from the refrigerator when in the lowest position. If the screw does come out of the rear roller bracket, the compartment access cover on the back of the refrigerator will have to be removed to reinstall the bolt.

2.Adjust the front leveling bolt to bring the refrigerator top parallel with the cabinet above the refrigerator. For standard cabinets, leave approximately ¹⁄₈ in. (3.18 mm) gap between the top hinges and the cabinet. For full-overlay cabinets, leave ¹⁄₄ in. (6.35 mm) gap for leveling. If you do not have a cabinet above the refrigerator, simply adjust the refrigerator to make it level.

1.For standard cabinets, leave ¹⁄₈ in. (3.18 mm) minimum clearance for leveling the refrigerator. For full-overlay cabinets, leave ¹⁄₄ in. (6.35 mm) minimum clearance for leveling and door clearance.

2.Front of the refrigerator.

3.Adjust the rear leveling bolt to bring the refrigerator level with the side cabinets or cabinet end panels.

4.If you want, you may now use the 4 leveling bolts to raise the refrigerator to close the gap between the refrigerator top hinge and the cabinet opening. Check that all 4 rollers still touch the floor and that the cabinet doors above the refrigerator open all the way.

Replace Base Grille

1.Open the refrigerator doors to 90°.

2.Replace the base grille.

Style 1 - Screw-on Base Grille:

■Place the grille in front of the base grille area.

■Use a screwdriver and guide the screws through the grille holes and into the screw clips located in the corner plates on each side of the opening. Tighten screws securely.

Style 2 - Snap-on Base Grille:

■Place the grille lower clips into the holes in the refrigerator panel. Roll the grille up toward the refrigerator until it snaps into place.

Complete Installation

1.Turn water supply line valve to “Open” position.

2.Turn refrigerator switch to ON position. Wait a few minutes. Check water line connections for leaks.

3.Set refrigerator and freezer compartment controls to the midpoint setting. Check that the compressor is operating properly and that all lights are working.

4.Flush water system before using. See the “Water System Prep” section in the Use and Care Guide.

NOTE: If construction will continue after refrigerator has been installed, set controls to OFF.

If refrigerator does not operate:

■Check that the circuit breaker is not tripped or house fuse blown.

■Check that the power supply cord is plugged into the outlet.

■See the “Troubleshooting” section located in the Use and Care Guide.

ASSISTANCE OR

SERVICE

If you have questions about operating, cleaning or maintaining your refrigerator:

■Refer to Use and Care Guide.

■Call the Customer Interaction Center. Check your Use and Care Guide for the number to call or phone the dealer from whom you purchased the appliance.

If you need service

Maintain the quality built into your refrigerator by calling an authorized service company.

To obtain the name and number of the authorized service company, do one of the following:

■Contact the dealer from whom you purchased your refrigerator.

■Look in the Yellow Pages of your telephone directory.

■Call the Customer Interaction Center. The number is listed in your Use and Care Guide.

When you call, you will need the refrigerator model number and serial number. Both numbers are listed on the model/serial rating plate located inside the refrigerator.

8