KitchenAid 30" (76.2 cm) installation instructions Now start, With range in kitchen

Now start...

With range in kitchen.

Put on safety glasses and gloves.

1. Remove shipping materials, tape and protective film from range. Keep

cardboard bottom and shipping base under range. Remove oven racks and parts package from inside oven. If you have a slide-in range, remove back vent package from range top. See Step 7 for installation.

cardboard corner posts

spacers

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

11.

Line up holes in anti-tip bracket with mounting holes in floor. Use the screws provided to fasten anti-tip bracket to floor.

NOTE: Anti-tip bracket must be mounted securely to the sub-floor. Depending on the thickness of your flooring, longer screws may be necessary to anchor the bracket to the sub-floor. Longer screws are available from your local hardware store.

Take 4 cardboard corner posts from the

2. carton. Stack one cardboard corner post on top of another. Repeat with the other two corner posts. Place corner posts lengthwise on

the floor in back of range so corner posts will support outer side edges of range as shown.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to follow this instruction can result in back or other injury.

3.	Firmly grasp the range and gently lay it on
	its back on the cardboard corner posts.
	Pull cardboard bottom and shipping base
4.
	firmly to remove.

25" (63.5 cm) countertop over 24" (61 cm) cabinet

anti-tip bracket template

Place the anti-tip bracket template on the

9. floor in the cabinet opening so that the left edge is against cabinet and the top edge is against the rear wall, molding or cabinet.

If countertop is deeper than 25 inches (63.5 cm), measure and mark a distance 25 inches (63.5 cm) in from front of countertop opening and align template with mark (or subtract 25 inches (63.5 cm) from the countertop depth and add the difference to the corresponding dimension).

Move range close to cabinet opening.

12. Remove cardboard or hardboard from under range.

Press on front of storage drawer and

13. release to open. Pull open to first stop position. Lift front of drawer to clear

white wheels in drawer guides. Remove drawer and set it aside on a protected surface.

5.	Use an adjustable wrench to loosen the
	leveling legs 1-1/2 turns.

Place cardboard or hardboard in front of

6. range. Stand range back up onto

cardboard or hardboard.

Rear vent must be installed.

If you have a slide-in range, remove the

7. outside screws from rear trim on range. Use screws to attach rear vent to range.

Check that the type of gas supply is

8. correct for this range. (See model/serial rating plate.)

If connecting to L.P. Gas, follow directions in Conversion Kit included in your literature package.

If connecting to Natural gas, go to Step 9.

25" (63.5 cm) A

Countertop overhangs cabinet side.

A = Difference between countertop depth and 25" (63.5 cm).

A

anti-tip bracket template

If countertop is not flush to the side of the cabinet opening, align the left side of the template to allow for the countertop overhang. Tape the freestanding range anti-tip bracket template in place.

Contact a qualified floor covering installer for the best procedure of drilling mounting holes through your type floor covering.

Before moving, slide range onto cardboard or hardboard.

To mount anti-tip bracket to wood floor,

10. use the anti-tip bracket template to mark where to drill mounting holes. Use

a drill with a 1/8" (0.3 cm) drill bit to drill the two mounting holes. Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use the anti-tip bracket template to mark where to drill mounting holes. Use a drill with a 3/16" (0.5 cm) masonry drill bit to drill the two holes. Remove template from floor. Tap plastic anchors into mounting holes in floor with hammer.

Carefully move range into final position.

14. Look under range (a flashlight may be needed) to check that left rear leveling

leg is engaged in the anti-tip bracket. If leveling leg is not properly engaged, remove and reposition the anti-tip bracket to ensure that the leveling leg fits properly in the anti-tip bracket.

Place rack in oven. Place level on rack,

15. first side to side; then front to back. If the range is not level, pull range

forward until the rear leveling leg is removed from the anti-tip bracket. Adjust the leveling legs up or down. Then slide range back into position. Check that leveling leg is engaged in anti-tip bracket.

NOTE: Oven must be level for satisfactory baking conditions.

Panel D