Installation Clearances

See NOTE

X

36" (91.4 cm) Countertop height

NOTE: The hood chimneys are adjustable and designed to meet varying ceiling or soffit heights depending on the distance “X” between the bottom of the hood and the cooking surface. For higher ceilings, a 40" (101.6 cm) Chimney Extension Kit Part Number 8212698 (Black), Kit Part Number 8212696 (Stainless Steel) or Kit Part Number 8212697 (White) is available. See your dealer. The chimney extension replaces the upper chimney shipped with the hood.

IMPORTANT:

Minimum distance “X”: 24" (61.0 cm)

Suggested maximum distance “X”: 30" (76.2 cm)

For vented installations, the chimneys can be adjusted for ceilings between 7’ 7¹⁄₈" (2.31 m) and 9' 1³⁄₄" (2.79 m).

For non-vented (recirculating) installations, the chimney can be adjusted for ceilings between 8' 3³⁄₈" (2.52 m) and 9' 5¹⁄₄" (2.88 m).

VentingRequirements

Vent system must terminate to the outside, except for non- vented (recirculating) installations.

Do not terminate the vent system in an attic or other enclosed area.

Do not use 4" (10.2 cm) laundry-type wall caps.

Use metal vent only. Rigid metal vent is recommended. Do not use plastic or metal foil vent.

The vent system must have a damper. If the roof or wall cap has a damper, do not use the damper supplied with the range hood.

For the most efficient and quiet operation:

Use a straight run or as few elbows as possible.

Use no more than three 90° elbows.

Make sure there is a minimum of 24" (61 cm) of straight vent between the elbows if more than 1 elbow is used.

Do not install 2 elbows together.

Use clamps to seal all joints in the vent system.

Use caulking to seal exterior wall or roof opening around the cap.

The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize backward cold air flow and a nonmetallic thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your area.

Venting Methods

This island hood is factory set for venting through the roof or wall.

A 6" (15.2 cm) round vent system is needed for installation (not included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance.

Vent system can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.

5

Page 5
Image 5
KitchenAid 36(91.4CM) ISLAND RANGE HOOD VentingRequirements, Installation Clearances, Cold weather installations

36"(91.4CM) ISLAND RANGE HOOD specifications

The KitchenAid 36" (91.4CM) Island Range Hood is an exceptional addition to any modern kitchen, combining functionality with sophisticated design. This hood is engineered to efficiently remove smoke, steam, and odors while enhancing the aesthetic appeal of your kitchen island setup.

One of the standout features of the KitchenAid Island Range Hood is its powerful ventilation system. With multiple speed settings, including a powerful boost function, it ensures optimal air circulation and keeps your kitchen environment fresh, regardless of the intensity of your cooking. The hood boasts a high CFM (cubic feet per minute) rating, allowing it to capture and vent even the most pungent cooking odors effectively.

The hood is designed with a sleek, stainless steel finish that complements any kitchen decor. Its modern appearance adds elegance and sophistication, making it not just a functional appliance, but also a statement piece in your kitchen. The adjustable duct cover allows for versatile installation heights, ensuring a perfect fit for various ceiling heights, making it an ideal choice for island installations.

Equipped with innovative technologies, the KitchenAid Island Range Hood features LED lighting that enhances visibility over your cooking area. The bright, energy-efficient lights illuminate your workspace without excessive heat, providing the right ambiance for culinary creativity. Additionally, it has a dishwasher-safe baffle filter, which traps grease and can be easily cleaned, ensuring the hood maintains its performance and appearance over time.

The hood also includes a convenient remote control feature, allowing you to adjust settings and switch the unit on and off from a distance. It integrates seamlessly with other KitchenAid appliances, creating a cohesive and modern kitchen environment.

Furthermore, noise levels are kept to a minimum, thanks to the hood’s design and advanced engineering, enabling you to enjoy a peaceful cooking experience. Whether you are a professional chef or a home cooking enthusiast, the KitchenAid 36" Island Range Hood offers the perfect blend of style, efficiency, and advanced technology—all essential elements for an exceptional cooking environment.