INSTALLATION INSTRUCTIONS

PrepareLocation

■It is recommended that the vent system be installed before hood is installed.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

■Check your ceiling height and the hood height maximum before you select your hood.

1.Disconnect power.

2.Determine which venting method to use: roof, wall, or non- vented.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface. Tip the hood on its back and remove filters and set aside.

To remove filters:

NOTE: Use 2 hands to remove the filters, one to pull and turn the knob, the other to hold the filter so that it doesn’t fall.

■Pull knob forward (toward the front of the hood) while turning the knob counterclockwise to release the locking lever.

■Slide the filter down and away from the the front retaining channel.

5.Slide apart the chimney covers.

NOTE: Do not remove the plastic covering on the chimney covers at this time. The covering protects the chimney during installation.

The chimney section of the hood is shipped assembled. It must be disassembled for installation.

6.Remove the lower chimney cover from the chimney support by removing the two Phillips screws on the outside bottom of the chimney cover.

7.Remove the upper chimney cover from the chimney support by removing the two Phillips screws on the outside top of the chimney cover.

8.Determine and mark the centerline on the ceiling where the hood will be installed, making sure that the hood is centered over the cooking surface.

9.Tape the template (supplied in the chimney support carton) to the ceiling and mark the mounting holes, electrical hole and vent location (if used) on the ceiling.

A

B

C

A. Template on ceiling

B.Centerline

C.Cooking surface

10.Drill pilot holes in the chimney support mounting hole locations for your attachment method.

11.Use a 1¹⁄₄" or 3.0 cm drill bit to drill the hole for the power supply cable.

12.If venting to the outside, cut the hole for the vent system in the ceiling and install the vent system. See “Venting Requirements” section.

13.If venting to the outside, place the round damper into the exhaust opening of the vent motor housing.

14.Remove the 4 chimney support ceiling attachment bolts from the parts bag and install in previously drilled pilot holes. Leave screw heads about ¹⁄₄" (6.4 mm) away from ceiling joists.

A

A. ¹⁄₄" (6.4 mm)

15.Run wire through the 1¹⁄₄" (3.0 cm) electrical hole in the ceiling according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough power supply cable from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical wiring box.

16.Use caulk to seal all openings.

NOTE: Do not reconnect power until installation is complete.

7

Page 6 Page 8
Page 7
Image 7
KitchenAid 36(91.4CM) ISLAND RANGE HOOD Installation Instructions, PrepareLocation, To remove filters
Page 6 Page 8

36"(91.4CM) ISLAND RANGE HOOD specifications

The KitchenAid 36" (91.4CM) Island Range Hood is an exceptional addition to any modern kitchen, combining functionality with sophisticated design. This hood is engineered to efficiently remove smoke, steam, and odors while enhancing the aesthetic appeal of your kitchen island setup.

One of the standout features of the KitchenAid Island Range Hood is its powerful ventilation system. With multiple speed settings, including a powerful boost function, it ensures optimal air circulation and keeps your kitchen environment fresh, regardless of the intensity of your cooking. The hood boasts a high CFM (cubic feet per minute) rating, allowing it to capture and vent even the most pungent cooking odors effectively.

The hood is designed with a sleek, stainless steel finish that complements any kitchen decor. Its modern appearance adds elegance and sophistication, making it not just a functional appliance, but also a statement piece in your kitchen. The adjustable duct cover allows for versatile installation heights, ensuring a perfect fit for various ceiling heights, making it an ideal choice for island installations.

Equipped with innovative technologies, the KitchenAid Island Range Hood features LED lighting that enhances visibility over your cooking area. The bright, energy-efficient lights illuminate your workspace without excessive heat, providing the right ambiance for culinary creativity. Additionally, it has a dishwasher-safe baffle filter, which traps grease and can be easily cleaned, ensuring the hood maintains its performance and appearance over time.

The hood also includes a convenient remote control feature, allowing you to adjust settings and switch the unit on and off from a distance. It integrates seamlessly with other KitchenAid appliances, creating a cohesive and modern kitchen environment.

Furthermore, noise levels are kept to a minimum, thanks to the hood’s design and advanced engineering, enabling you to enjoy a peaceful cooking experience. Whether you are a professional chef or a home cooking enthusiast, the KitchenAid 36" Island Range Hood offers the perfect blend of style, efficiency, and advanced technology—all essential elements for an exceptional cooking environment.
Top Page Image Contents