Personal Injury/Product Damage
Hazard
Avoid opening dishwasher door before dishwasher is installed.
If dishwasher is to be installed freestanding, not in cabinet enclosure, dishwasher must be secured to the floor using Kit No. 4162841, available from your local dealer.
Failure to follow these instructions may result in personal injury or product damage.
Floor Damage
Keep cardboard shipping base or plywood under dishwasher until it is installed or slide dishwasher onto cardboard or hardboard before moving across the floor.
Failure to do so may cause damage to floor covering.
Important:
Observe all governing codes and ordinances.
Electrical Shock Hazard l Electrical ground is required.
l Electrical wiring and components
must not contact any plumbing materials or drain hose.
l Electrical wiring, water supply line, and drain line must not contact any exposed terminals of the dishwasher wiring.
Product Dimensions
Side View | Rear View |
L-2611 -_I
It is your responsibility to:
. Comply with the installation specifications and dimensions.
l Properly install dishwasher.
lMake sure you have everything necessary for proper installation.
l Contact a qualified installer to insure that the electrical and plumbing installations meet national and local codes and ordinances.
l Provide a properly grounded outlet.
|
|
|
|
| Corner location | - | 2” min. door |
|
|
| ||
|
|
|
|
|
| to cabinet | or | wall. |
|
|
| |
|
|
|
| Cut 1” | diameter | water | line | Grommet | (Part |
|
| |
|
|
|
| drain | line, and | power | cord | No. 302797) |
|
| ||
|
|
|
| openings | within | shaded | area. | required for |
|
| ||
|
|
|
|
|
|
|
|
| electrical | hole cut |
|
|
|
|
|
|
|
|
|
|
| in metal | cabinet. |
|
|
35” | max.. |
|
| Unshaded | area must | be |
|
| - | |||
’ |
| free ofg;ip;Lz;zs, | and |
|
| min. | ||||||
|
|
|
|
|
|
|
|
|
| |||
min. | with |
|
|
|
|
|
|
|
|
| 2” |
|
leveling |
|
|
|
|
|
|
|
| b | 36” | ||
legs |
|
|
|
|
|
|
|
| ||||
removed. |
|
|
|
|
|
|
|
|
| b |
| |
F!ote:ll |
|
|
|
|
|
|
|
| . |
| ||
Measure |
|
|
|
|
|
|
|
| ‘\ |
| ||
from | lowest |
|
|
|
|
|
|
| I |
| ||
point of |
| 1 |
|
|
|
|
|
|
| |||
underside | of | 8” |
|
|
|
|
|
| ||||
countertop. |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
l Plumbing and wiring should not cross in front of motor or dishwasher.
Failure to follow these instructions could result in electrical shock.
Fire Hazard
l Do Not install dishwasher over carpeted flooring.
l Do Not pinch power supply cord or kink power supply cable between dishwasher and cabinet.
. Cabinet opening must completely enclose sides, top and back of dishwasher. A side panel and wood top are available from your KitchenAid dealer for installing the dishwasher at the end of a cabinet.
Failure to do so may result in fire.
|
|
| Important: | Observe all |
| dishwasher fill | governing | codes and | |
I | ordinances. |
| ||
| valve location |
| ||
| v |
| 24” |
|
It is recommended that the electrical, drain and water supply lines be located as close to the rear wall as possible.
Check location where dishwasher will be installed. Location must provide:
lEasy access to water, electricity and drainage lines.
l | Convenient |
| loadin | best position |
|
|
|
|
| ||||||
| is to the ri ht or le;: of a sink. |
|
|
|
|
|
|
| |||||||
l | Openin | t%at is square | for | proper |
|
|
|
|
|
| |||||
| dishwas ?Ier operation and appearance. |
| 2 adjustable |
|
| ||||||||||
l | Cabinet | front | that | is perpendicular | to | l |
|
| |||||||
| floor. |
|
|
|
|
|
|
|
|
|
| wrenches |
| for | fittin |
| Protection | so that | water | inlet | valve | and |
| copper | tubing; | or s | |||||
l |
| pipe wrenches. | for | ||||||||||||
| drain | cannot | freeze. |
|
|
|
|
| $gagn:‘zed | or | Iron | ||||
l l/4” minimum clearance between |
|
| bushing |
|
|
| |||||||||
| motor |
| and | flooring | to prevent | the | motor | l |
|
|
| ||||
| from | overheating. |
|
|
|
|
| l l/2” O.D. co per | |||||||
|
|
|
|
|
|
| tubing; | or | 3PI18 |
l l
l
l
l l
measurin tape 3/4” nut %river or socket wrench Phillips screwdriver
pliers
shutoff valve
Product Damage Protect dishwasher and water lines leading to dishwasher against freezing.
Failure to do so could cause inlet valve, water lines and drain hose to rupture. Such ruptures are not covered by the warranty.
Proper electrical, drain and water supply lines must be installed within shaded area to prevent interference with dishwasher cabinet or other components.
For installations where dishwasher will be left unused and subjected to freezing temperatures, see “Winterizing” section of Use and Care Guide.
l 1” drill bit or hole saw
l electric drill
l electrical tape l
screwdriver
l grommet (metal cabinets)
l 9/16” I.D. heat- and
2 screws
: ‘p;T;I’ NPT sireet elbows or 90” compression elbows with 3/8” NPT at one end for copper line
l 3/4” strain relief l supply line
fittings
l tubing cutter l
l wire cutters l drain hose
llevel