5.Unplug the wiring harness from the left side of the cutter grid.

■Replace the ice scoop holder by aligning the rear hook with the opening (the holder angles down slightly). Slide the holder back fully until the front rests securely on the cutter grid cover.

1.Cutter Grid Cover

2.Screws

6.Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7.Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

1.

Cutter Grid Harness

4.

Ice Level Sensor Harness

2.

Screw

5.

Plastic Spacer

3.

Cutter Grid

6.

Screw

8.Remove the two thumb screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side.

1.Water Pan

2.Water Pan Thumb Screws

3.Drain Cap

9.Remove, clean and replace the ice scoop and ice scoop holder.

■After removing the ice scoop, remove the holder by lifting the front free from the cutter grid cover. Then lift the back of the holder slightly to release the rear hook and pull forward.

■Wash the ice scoop holder along with the other interior components using the following instructions.

1.Ice Scoop Holder

10.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tablespoon (15 mL) of household bleach in 1 gallon (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

11.Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws.

12.Check the following:

■Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

■Hose from water pan is inserted into storage bin drain opening.

13.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

14.Plug in ice maker or reconnect power.

Changing the Light Bulb

The ice maker has a light bulb in the top of the storage bin. To replace it, open the bin door and follow these instructions:

1.Unplug ice maker or disconnect power.

2.Remove the three screws that hold the cutter grid cover in place. Reach behind the control panel and pull the light bulb down from the ceiling.

3.Replace with a 12-volt wedge base-type bulb (automotive #917). Locate the light bulb receptacle in the ceiling behind the control panel. Align the flat edge of the light bulb with the receptacle and snap the bulb into place.

4.Replace the cutter grid cover with three screws.

5.Plug in ice maker or reconnect power.

11

Page 10 Page 12
Page 11
Image 11
KitchenAid ICEMAKER manual Changing the Light Bulb
Page 10 Page 12

ICEMAKER specifications

The KitchenAid ICEMAKER is a remarkable appliance that brings convenience and efficiency to your home, ensuring a steady supply of fresh, crystal-clear ice. With its sleek design and user-friendly features, it is an essential addition for anyone who enjoys entertaining or simply wants to enhance their everyday lifestyle.

One of the standout features of the KitchenAid ICEMAKER is its impressive production capacity. It can produce up to 28 pounds of ice per day, allowing you to host gatherings without worrying about running out of ice. Its generous storage bin holds up to 25 pounds of freshly made ice, ensuring you always have enough on hand for parties, barbecues, or family gatherings.

The technology behind the KitchenAid ICEMAKER is designed for optimal performance and energy efficiency. It employs a high-efficiency compressor that not only ensures rapid ice production but also reduces energy consumption. With its robust cooling system, the appliance operates quietly, making it suitable for use in any room of the house.

A key characteristic of the KitchenAid ICEMAKER is its ability to produce clear, restaurant-quality ice. The machine uses a unique freezing process that eliminates impurities, resulting in clear cubes that melt slowly, keeping your beverages colder for longer without diluting their flavor. This feature is particularly appreciated by cocktail enthusiasts and those who enjoy high-quality drinks.

The ICEMAKER features intuitive controls that make operation simple and straightforward. With a digital display, users can easily monitor and adjust their ice-making preferences. The self-cleaning function is another noteworthy attribute, as it helps maintain hygiene and ensures the longevity of the appliance, requiring minimal user intervention.

Moreover, the KitchenAid ICEMAKER is designed for versatility, with options for different ice sizes to accommodate various drink types, from cocktails to soft drinks. Its built-in water filtration system ensures that every batch of ice is made with clean, fresh water, enhancing the quality of the ice while eliminating any unpleasant aftertaste.

Overall, the KitchenAid ICEMAKER combines functionality, quality, and style in one compact unit. Whether you're an avid entertainer or someone who simply enjoys the luxury of having ice on hand, this appliance is an excellent choice that will elevate your culinary experience. Its cutting-edge technology and thoughtful features make it a must-have for any modern kitchen.
Top Page Image Contents