KitchenAid KGCU484V dimensions Product Model Numbers, Location Requirements, Product Dimensions

Commercial Style Gas Cooktop

PRODUCT MODEL NUMBERS

KGCU407V KGCU482V

KGCU462V KGCU483V

KGCU463V KGCU484V

KGCU467V

Type of Gas

Natural Gas:

This cooktop is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

This cooktop is factory-set for use with Natural gas. To convert to LP gas, see the Gas Conversion instructions provided in the package containing literature. The model/ serial rating plate located on the left underside of the cooktop burner base has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the cooktop from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. To convert to LP gas, use the LP gas conversion kit provided with the cooktop and see the “Gas Conversions” section.

Gas Supply Line

●Provide a gas supply line of ³⁄₄" (1.9 cm) rigid pipe to the cooktop location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ¹⁄₂" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape.

Flexible metal appliance connector:

● If local codes permit, a new CSA design-certified, 4 - 5 ft

(122 - 152.4 cm) long, ⁵⁄₈" (1.6 cm) or ³⁄₄" (1.9 cm) I.D.,

flexible metal appliance connector may be used for

connecting the cooktop to the gas supply line.

● Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the cooktop enclosure or cabinet. It should be

in a location that allows ease of opening and closing. Do

LOCATION REQUIREMENTS

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner base.

It is recommended that a 600 CFM or larger vent hood be installed above the cooktop.

It is not recommended that a microwave hood combination be mounted above the cooktop.

The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

All openings in the wall or floor where cooktop is to be installed must be sealed.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

PRODUCT DIMENSIONS

CD

E

BA

A. 30"	7	C. Model/serial rating plate (located on the
	(76.2 cm) cooktop: 29⁷⁄₈" (75.9 cm)
36"	7	underside of the cooktop burner base)
	(91.4 cm) cooktop: 35⁷⁄₈" (91.1 cm)
48"	7	D. Island trim or optional backguard
	(121.9 cm) cooktop: 47⁷⁄₈₈" (121.6 cm)
B. 36"	(91.4 cm) long 3 prong grounding-type	E. 27	70.5 cm)

power supply cord

not block access to shutoff valve. The valve is for turning

on or shutting off gas to the cooktop.

B

A

C

A. Gas supply line

B. Shutoff valve “open” position

C. To cooktop

Electrical:

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit

G

F

A. 2770.5 cm)

C. 7⁷⁄₁₆" (18.8 cm)

A

E

Side View of Cooktop

B

C

D

E. 22" (55.9 cm)

F.3⁵⁄₈" (9.2 cm) G. 1" (2.6 cm)

serving only this cooktop be provided.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

D. Gas inlet is located 1⁷⁄₈" (4.8 cm) from the back of

the cooktop burner base and 4⁷⁄₈" (12.4 cm) in from left-hand side of the cooktop burner base.

Page 1 of 2

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10526088A
Instructions packed with product. Specifications subject to change without notice.	5/6/13