Level and Align Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1.Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be off the floor.

AB

C

¹⁄₄" (6 mm) max.

2" (5 cm)

D

A. Center board ¹⁄₄" (6.35 mm) max. above refrigerator

B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch-pounds

(5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.

4.For Classic and Overlay models, additional adjustments may be needed after the custom panels are installed.

A B

A

B

A. Rear leveling bolt

B. Front leveling bolt

2.Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

3.Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

Install Classic Series Custom Panels

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panels

1.Remove all tape and door bracing from the refrigerator and freezer doors.

2.Remove the screws that attach the handles to the door frame.

3.Slide the decorative door panels into the door frames.

4.If needed, route the door panels or install a filler panel between the doors and the decorative panels. See the “Classic Series Custom Panels” section in “Installation Requirements.

AA

A. Panels

23

Page 23
Image 23
KitchenAid KSSC42FTS, KSSC48FTS, KSSC36FTS Level and Align Refrigerator, Install Classic Series Custom Panels, Door Panels

KSSC36FTS, KSSC42FTS, KSSC48FTS specifications

The KitchenAid KSSC48FTS, KSSC42FTS, and KSSC36FTS are premium built-in side-by-side refrigerators designed for modern kitchens. These models not only provide ample storage but also incorporate advanced technologies and distinctive features that cater to culinary enthusiasts and everyday users alike.

The KitchenAid KSSC48FTS is the largest of the trio, offering an impressive 48-inch width and a generous capacity that provides ample space for fresh and frozen foods. It features a sleek stainless steel exterior with a commercial-inspired design that brings a professional touch to any kitchen. One standout characteristic is its ExtendFresh Temperature Management System, which utilizes sophisticated sensors and a dual cooling system to maintain optimal temperatures in both the refrigerator and freezer compartments. This helps preserve the freshness of perishable foods longer.

The KSSC42FTS, with a 42-inch width, retains many of the premium features found in its larger counterpart while providing slightly less capacity. It also includes the ExtendFresh system and is equipped with a FreshChill Temperature-Controlled Drawer that offers adjustable temperature settings, perfect for storing delicate items like wines and cheeses. Additional features include a water filtration system that reduces contaminants, ensuring that every glass of water is pure and refreshing.

At the heart of the KitchenAid KSSC36FTS is its 36-inch design, tailored for kitchens where space is a concern without compromising performance and style. Like the other models, it features the ExtendFresh system, along with an innovative Preserva Food Care System that helps to manage humidity levels in the refrigerator, preventing food spoilage. Each model boasts adjustable spill-resistant shelves, enhancing organization and making cleanup easier.

In terms of usability, all three models come equipped with interior LED lighting, providing bright illumination to help you easily find what you need. The appliances also feature a user-friendly control panel that allows for precise temperature adjustments and settings.

The KitchenAid KSSC series is built not just for function but also for performance and convenience, providing users with a perfect blend of style, technology, and capacity. Whether you opt for the KSSC48FTS, KSSC42FTS, or KSSC36FTS, you’ll enjoy a premium refrigeration experience tailored to meet your kitchen needs.