Installation Requirements, Tools and Parts

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■Installer: Leave Installation Instructions with the homeowner.

■Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.

Tools Needed

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■	Cordless drill	■	Torx®†T27 screwdriver
■	Drill bits	■	¹¹⁄₃₂" Nut driver
■	Two adjustable	■	³⁄₈" and ¹⁄₂" Open-end wrenches
	wrenches	■	⁵⁄₃₂" Hex key
	Phillips screwdriver
■		■	¹⁄₄" and ⁵⁄₁₆" Socket drivers
	Small level
■		■	Tape measure
	Appliance dolly
■		■	Utility knife

Parts Needed

■Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

■One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

■Order factory panels, make custom panels or consult a qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Classic Series Custom Panels” for more information.

Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Overlay Series Custom Panels and Handle Kits” for more information.

Architect® and Complete Series are shipped complete.

■If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting.

Location Requirements

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

■Observe all governing codes and ordinances.

■It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

■Do not install in a location where the temperature will fall below 55°F (13°C).

■Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels and contents of the refrigerator.

■Ceiling height must allow for side tipping radius. See “Tipping Radius.”

■Location should permit door to open fully. See “Door Swing Dimensions.”

■Location must permit top grille removal. See “Opening Dimensions.”

Opening Dimensions

■To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the floor. See “Install Anti-Tip Boards” for more information.

NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained above the top grille in order for the top grille to be removed.

¹⁄₂"

(1.3 cm)

†®TORX is a registered trademark of Saturn Fasteners, Inc.

KSSC36FTS, KSSC42FTS, KSSC48FTS specifications

The KitchenAid KSSC48FTS, KSSC42FTS, and KSSC36FTS are premium built-in side-by-side refrigerators designed for modern kitchens. These models not only provide ample storage but also incorporate advanced technologies and distinctive features that cater to culinary enthusiasts and everyday users alike.

The KitchenAid KSSC48FTS is the largest of the trio, offering an impressive 48-inch width and a generous capacity that provides ample space for fresh and frozen foods. It features a sleek stainless steel exterior with a commercial-inspired design that brings a professional touch to any kitchen. One standout characteristic is its ExtendFresh Temperature Management System, which utilizes sophisticated sensors and a dual cooling system to maintain optimal temperatures in both the refrigerator and freezer compartments. This helps preserve the freshness of perishable foods longer.

The KSSC42FTS, with a 42-inch width, retains many of the premium features found in its larger counterpart while providing slightly less capacity. It also includes the ExtendFresh system and is equipped with a FreshChill Temperature-Controlled Drawer that offers adjustable temperature settings, perfect for storing delicate items like wines and cheeses. Additional features include a water filtration system that reduces contaminants, ensuring that every glass of water is pure and refreshing.

At the heart of the KitchenAid KSSC36FTS is its 36-inch design, tailored for kitchens where space is a concern without compromising performance and style. Like the other models, it features the ExtendFresh system, along with an innovative Preserva Food Care System that helps to manage humidity levels in the refrigerator, preventing food spoilage. Each model boasts adjustable spill-resistant shelves, enhancing organization and making cleanup easier.

In terms of usability, all three models come equipped with interior LED lighting, providing bright illumination to help you easily find what you need. The appliances also feature a user-friendly control panel that allows for precise temperature adjustments and settings.

The KitchenAid KSSC series is built not just for function but also for performance and convenience, providing users with a perfect blend of style, technology, and capacity. Whether you opt for the KSSC48FTS, KSSC42FTS, or KSSC36FTS, you’ll enjoy a premium refrigeration experience tailored to meet your kitchen needs.

KitchenAid KSSC48FTS, KSSC36FTS Installation Requirements, Tools and Parts, Location Requirements

Models: KSSC36FTS KSSC42FTS KSSC48FTS