3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

5.Determine and mark the centerline on the wall where the canopy hood will be installed.

6.Select a mounting height between a minimum of

24" (61.0 cm) for an electric cooking surface, a minimum

of 27" (68.6 cm) for a gas cooking surface, and a suggested maximum of 36" (91.4 cm) above the range to the bottom of the hood. Mark a reference line on the wall.

7.Tape template in place, aligning the template centerline and bottom of template with hood bottom line and with the centerline marked on the wall.

A

DRILL2 (TW O)3/16"PILOTHOLESTHROUGH STUDSOR REAR W ALLSUPPORT

Vertical Centerline

REAR W ALL

M OUNTING TEM PLATE

C

L

ALIGN BOTTOM EDGE

W ITH PENCILLINE

INDICATING BOTTOM

OFTHEHOOD

Installation Height

HorizontalLine

BC

A.Centerline

B.Fastener locations

C.Mounting height reference

8.Mark centers of the fastener locations through the template to the wall.

IMPORTANT: All canopy mounting screws must be installed into wood. If there is no wood to screw into, additional wall framing supports may be required.

Remove the template.

9.Drill ³⁄₁₆" (4.8 mm) pilot holes at all locations where screws are being installed into wood.

10.Install 2 - 5 x 45 mm mounting screws. Leave a ¹⁄₄" (6.4 mm) gap between the wall and the back of the screw head to slide range hood into place.

¹⁄₄" (6.4 mm)

Vent Cover Support Bracket Installation

Installations using telescoping upper and lower vent cover assembly

1.Position vent cover bracket on wall about ¹⁄₈" (3.0 mm) away from the ceiling.

2.Mark the hole locations.

3.Drill ³⁄₈" (9.5 mm) holes for wall anchors and insert anchors flush with the wall.

AC

B

D

A. 8 x 40 mm drywall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 5 x 45 mm screws

4.Attach vent cover support bracket to wall.

Complete Preparation

1.Determine and make all necessary cuts in the wall for the vent system. Install the vent system before installing the hood. See “Venting Requirements” section.

2.Determine the required height for the home power supply cable and drill a 1¼" (3.2 cm) hole at this location.

3.Run the home power supply cable according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough ½" conduit and wires from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4.Use caulk to seal all openings.

Install Range Hood

1.Using 2 or more people, hang range hood on 2 mounting screws through the mounting slots on back of hood.

A

B

C

A. Mounting screws

B. Mounting slots

C. Lower mounting screws

2.Remove the grease filter. See “Range Hood Care” section.

3.Level the range hood and tighten upper mounting screws.

4.Install 2 - 5 x 45 mm lower mounting screws and tighten.

7

Page 6 Page 8
Page 7
Image 7
KitchenAid LI3Y7C/W10322991C Install Range Hood, Range Hood Mounting Screws Installation, Complete Preparation
Page 6 Page 8

LI3Y7C/W10322991C specifications

The KitchenAid LI3Y7C/W10322991C is a versatile and innovative appliance that embodies modern kitchen technology and design. This model, known for its robust construction and sleek aesthetics, is a prime example of KitchenAid's dedication to blending functionality with elegance.

One of the standout features of the LI3Y7C is its advanced motor system, designed to provide exceptional power while maintaining quiet operation. This ensures that you can mix even the thickest batters without disturbing the pleasant ambiance of your kitchen. The motor's efficiency also translates into longer-lasting performance, making it a reliable companion for daily cooking tasks.

The LI3Y7C boasts a unique planetary mixing action. This technology rotates the bowl and the beater simultaneously, ensuring complete mixing coverage and eliminating the need for manual scraping. With multiple speed settings, users can easily adjust for different recipes, whether they're blending, kneading, or whipping.

A key characteristic of this model is its spacious mixing bowl, which allows for larger quantities of ingredients. Made from stainless steel, the bowl is not only durable but also easy to clean, making maintenance a breeze. The ergonomic handle provides a comfortable grip, enhancing usability during food preparation.

Another notable aspect is the versatility offered by the LI3Y7C, as it’s compatible with a wide array of KitchenAid attachments. From pasta makers to food grinders, these attachments expand the appliance's functionality, allowing it to perform multiple culinary tasks. This adaptability makes it an indispensable tool for both novice cooks and seasoned chefs.

Safety features are also prioritized in the design of the LI3Y7C. The appliance includes a built-in overload protection system, which prevents the motor from overheating during extended use. This not only ensures longevity but also offers peace of mind to users.

In terms of aesthetics, the KitchenAid LI3Y7C/W10322991C is available in various colors to suit different kitchen decors. Its timeless design and compact size allow it to fit seamlessly into any countertop space, enhancing the kitchen's overall look.

In summary, the KitchenAid LI3Y7C/W10322991C stands out for its powerful motor, advanced planetary mixing action, generous mixing bowl, and compatibility with a wide range of attachments. These features, combined with a focus on safety and design, make it an essential addition to any kitchen. Whether you're baking a cake, whipping cream, or preparing dough, this appliance delivers consistent results, helping you create delicious meals with ease.
Top Page Image Contents