Installation Instructions

Example Vent System

90 elbow		Wall cap
	6 ft (1.8 m)	Wall cap
	6 ft (1.8 m)

2ft

(0.6 m)

The following example falls within the maximum recommended vent length of 35 ft (10.7 m).

1	- 90° elbow	= 5.0 ft (1.5 m)
1	- wall cap	= 0.0 ft (0.0 m)
8 ft (2.4 m) straight		= 8.0 ft (2.4 m)

Length of system		= 13.0 ft (3.9 m)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

■If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

Prepare Location

■It is recommended that the vent system be installed before hood is installed.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

■Check your ceiling height and the hood height maximum before you select your hood.

1.Disconnect power.

2.Determine which venting method to use: roof, wall, or non- vented.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

1.Determine and mark the centerline on the wall where the canopy hood will be installed.

2.Select a mounting height between a minimum of 24"

(61.0 cm) for an electric cooking surface, a minimum of 27" (68.6 cm) for a gas cooking surface, and a suggested maximum of 36" (91.4 cm) above the range to the bottom of the hood. Mark a reference line on the wall.

3.Tape template in place, aligning the template centerline and bottom of template with hood bottom line and with the centerline marked on the wall.

DRILL2 (TW O)3/16"PILOTHOLESTHROUGH STUDSOR REAR W ALLSUPPORT

Vertical
Centerline	REAR W ALL
	M OUNTING TEM PLATE

ALIGN BOTTOM EDGE

W ITH PENCILLINE

INDICATING BOTTOM

OFTHEHOOD

Installation Height

HorizontalLine

A.Centerline

B.Fastener locations

C.Mounting height reference (hood bottom line)

LI3Y9B/W10320584E specifications

The KitchenAid LI3Y9B/W10320584E is a highly efficient and versatile stand mixer designed to meet the demands of both amateur cooks and professional chefs. Renowned for its durability and performance, this kitchen appliance is a staple in many households.

One of the standout features of the LI3Y9B is its powerful motor, which drives the mixing process with ease. With a robust horsepower, this stand mixer can handle even the toughest doughs and ingredient mixtures. The motor is designed to provide consistent power, ensuring that precise mixing is achieved every time.

The mixer features a tilt-head design, allowing for easy access to the mixing bowl and attachments. This design enhances convenience during food preparation, making it simple to add ingredients or switch out mixing tools. The generous bowl capacity is another plus, accommodating large batches of dough or batter, which is particularly beneficial for baking enthusiasts.

In terms of versatility, the KitchenAid LI3Y9B/W10320584E comes equipped with multiple speed settings that cater to a wide range of mixing tasks. Whether you are whipping cream, kneading bread dough, or mixing cookie batter, you can easily adjust the speed to suit your needs. The inclusion of various attachments enhances its functionality, allowing users to tackle an array of culinary tasks, from shredding cheese to making pasta.

The mixer is constructed with high-quality materials built to last, ensuring that it can withstand the rigors of daily use. The design is not only practical but also aesthetically pleasing, available in various colors to complement any kitchen décor.

Another noteworthy characteristic is its ease of cleaning. The bowl and attachments are dishwasher safe, making cleanup after cooking or baking a breeze. Additionally, the mixer’s design minimizes the risk of ingredient splatter, providing a cleaner cooking experience.

In summary, the KitchenAid LI3Y9B/W10320584E stands out for its powerful motor, versatile speed settings, durable construction, and user-friendly features. Whether you are an everyday home cook or a baking aficionado, this stand mixer is an excellent addition to any kitchen. Its combination of performance, functionality, and style makes it a valuable tool for culinary creativity.

KitchenAid LI3Y9B/W10320584E Installation Instructions, Electrical Requirements, Prepare Location

Models: LI3Y9B/W10320584E

Example Vent System

Electrical Requirements