KitchenAid Pro LineTM Operation, Cleaning, Optional Installation Kits available from your dealer

Replacing the Halogen lamps:

36" (91.4 cm) and 42" (106.7 cm) hoods shown.

Before you begin, make sure that the range hood is turned off and that the other lamps have had sufficient time to cool. Halogen bulbs burn extremely hot.

To replace a halogen lamp:

•Remove 2 screws from the circular metal trim around the lamp assembly.

•Pull the trim with the lamp assembly attached down far enough so that the lamp can be pushed out of the socket.

•Insert the new lamp into the socket and push the lamp and trim assembly back up into the hood.

•Replace the trim.

Operation

The canopy hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen.

Opening the canopy hood control panel:

The hood controls are located on the right-hand underside of the canopy.

controls

light	blower	blower speed
switch	switch	switch

Operating the light:

ON: Move the light switch to the “1” position.

OFF: Move the light switch to the “0” position.

Operating the blower:

ON: Move the blower switch to the “1” position.

OFF: Move the blower switch to the “0” position.

Adjusting the blower speed:

The blower has three speed control.

Move the blower speed switch to: “1” position for low speed,

“2” position for medium speed, or “3” position for high speed.

Cleaning

Filters:

The filters should be washed frequently. Place metal filters in dishwasher or hot detergent solution to clean.

To remove filters:

Note: Use two hands to remove filters, one to pull and turn the knob, the other to hold the filter so that it doesn’t fall onto the cooktop.

•Pull knob forward, toward the front of the hood, while turning the knob to the left (counter- clockwise) to release the locking lever.

To reinstall filters, see Step 16.

Exterior surfaces:

•Do not use steel wool or soap- filled scouring pads.

•Rub in direction of the grain line to avoid marring the surface.

•Always wipe dry to avoid water marks.

•KitchenAid® Professional Formula Stainless Steel Cleaner & Polish is the cleaner recommended for cleaning stainless steel surfaces on this product.To order call our Customer Service Center at

1-800-442-9991 or order on-line at www.applianceaccessories.com and ask for part number 8171420. To order from Canada, call 1-800-807-6777.

•If commercial cleaners are used, follow label directions. Do not use products that contain chlorine (bleach). Chlorine is a corrosive substance.

For routine cleaning and fingerprints, use liquid detergent soap and water, or all-purpose cleaner. Wipe with damp cloth or sponge, then rinse with clean water and wipe dry.

Installation kits available from your dealer

Optional Installation Kits available from your dealer.

Note: Kits are available in stainless steel only.

Backsplash: Must be installed before hood is installed. 30" (76.2 cm) hood: Kit No. 8285148

36" (91.4 cm) hood: Kit No. 8284756

42" (106.7 cm) hood: Kit No. 8284827

48" (121.9 cm) hood: Kit No. 8284755

Vent covers: 12" (30.5 cm) high, 12" (30.5 cm) deep. 30" (76.2 cm) hood: Kit No. 8285149

36" (91.4 cm) hood: Kit No. 8284753

42" (106.7 cm) hood: Kit No. 8284828

48" (121.9 cm) hood: Kit No. 8284752

Chimney extensions: extends from 12" (30.5 cm) to 23" (58.4 cm) high. For use with 30" (76.2 cm), 36"

(91.4 cm), 42" (106.7 cm) and 48" (121.9 cm) hoods: Kit No. 8284754

Vent transition: transitions from two 3-1/4" x 10"

(8.3 x 25.4 cm) vents to one 10" (25.4 cm) round vent. Not for use with chimney extension Kit No. 8284754.

30" (76.2 cm) hood: Not available

36" (91.4 cm) hood: Not available

42" (106.7 cm) hood: Not available

48" (121.9 cm) hood: Kit No. 8284757

9