Dishwasher Feedback Section

CONTROLS AND CYCLE STATUS

CONTROL

PURPOSE

COMMENTS

 

 

 

 

 

 

 

 

The Cycle Status Indicator

Clean indicator glows when a cycle is finished.

 

 

 

Lights are used to follow the

If you select the Sani Rinse option, when the Sani Rinse cycle is finished,

 

 

 

progress of the dishwasher

 

 

 

the Sanitized indicator glows. If your dishwasher did not properly sanitize

 

 

 

cycle. They are located on

 

 

 

your dishes, the light flashes at the end of the cycle. This can happen if the

 

 

 

the top of the door.

 

 

 

cycle is interrupted, or the water could not be heated to the required

 

 

 

 

 

 

 

 

temperature.

 

 

 

 

The Clean and Sanitized lights go off when you open and close the door or

 

 

 

 

press and hold CANCEL/DRAIN.

 

 

 

 

 

 

 

 

The Cycle Status Display is

The indicators will inform you if you are able to add a dish to the cycle after

 

 

 

 

 

 

used to follow the progress

it has started. It will also inform you if the dishwasher is washing, rinsing,

 

 

 

of the dishwasher cycle, and

drying, complete, and/or sanitized. They will show whether the control is

 

 

 

to show other information.

locked and/or the delay option is selected. A series of bars will count down

 

 

 

 

the duration of the cycle remaining from left to right. Each bar equals

 

 

 

 

approximately 24 minutes of cycle length. The bars will also count down

 

 

 

 

the delay feature from left to right, and the delay indicator will be activated.

 

 

 

 

After every 30 cycles, the dishwasher will display “affresh,” providing a

 

 

 

 

temporary reminder for you to perform a monthly maintenance procedure.

 

 

 

 

See “Dishwasher Care” section.

 

 

 

 

 

Canceling a Cycle

1.Open the door slightly to stop the cycle. Wait for the spraying action to stop before completely opening the door.

2.Press and hold CANCEL/DRAIN button once. The Cancel/ Drain light will light up.

3.Close the door and the dishwasher starts a drain cycle (if water remains in bottom of dishwasher). Let the dishwasher drain completely. The Cancel/Drain light turns off after 2 minutes.

Changing a Cycle After Dishwasher Is Started

1.You can interrupt a cycle and restart your dishwasher from the beginning using the following procedure.

2.Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely.

3.Check that detergent dispenser cover is still closed. If cover is open, you will need to refill the detergent dispenser before restarting your new cycle.

4.Press and hold CANCEL/DRAIN twice to reset the control.

5.Select new cycles and options.

6.Press START/RESUME.

Adding a Dish After Dishwasher Is Started

1.Check if the Add Dish indicator is lit on the Cycle Status Display.

2.Open the door slightly to stop the cycle. Wait for the spraying action to stop, and then open the door completely.

3.Check whether the detergent dispenser cover is still closed. If it is open, the wash cycle has already started and adding a dish is not recommended.

4.If detergent has not yet been used (detergent dispenser cover is closed), you may add a dish.

5.Press START/RESUME.

11

Page 11
Image 11
KitchenAid W10656164B warranty Dishwasher Feedback Section, Canceling a Cycle, Changing a Cycle After Dishwasher Is Started