Finalizing the Assembly

Final Adjustments

Fitting Spikes (P-38F and P-37F only)

 

The loudspeakers are supplied with a set of long spikes and a

 

set of short spikes. All are adjustable and fit in the same way.

 

Spike seats with felt bases are supplied for use where spikes

 

are inappropriate; e.g., on stone, hardwood or marble floors.

Collar

The spikes may be fitted with sets of short spikes, sets of

Shaft

long spikes or as a combination of two short spikes at the

Spike

front and two long spikes at the rear to assist with imaging,

 

(Refer to the next page)

 

Fitting Spikes (P-27C only)

Spike Seat

 

The P-27C also has spikes that should be used if the speaker

 

is not placed on a dedicated speaker stand. There are two

 

short front spikes with spike seats that should be installed

 

in the same manner as described above for the P-38F and P-37F. There is a third spike seat for use with either of the two rear spikes. The long-barrel rear spike should be used in applications where the speaker needs to be positioned either flat or with a degree of downward tilt. The short-barrel rear spike should be used in applications where the speaker needs to be positioned with a degree of upward tilt. This will often be the case in installations where the speaker is placed below a large projection screen.

Method: Run the textured collar halfway down the threaded shaft away from the spike point. Insert the shaft into the plinth and screw in tight. Now run the collar up to the plinth and lock it finger tight. Repeat for all four spikes.

Hint: If you feel that you may have to move the speakers around a lot before you get them exactly right, it is advisable to start out with the spikes resting in their spike seats. This will allow you to easily slide the speakers on a hard floor surface After finalizing the speaker position, you can then mark the position of the feet and remove the spike seats.

Dressing the Cables

If there is more than one cable to each loudspeaker, gather them and lay them side by side. Make sure you have identification on all the cables. Ensure the cables are connected the same way all around with no loose or faulty connections.

Leveling the Loudspeakers

If the floor is not perfectly level, you will find that one spike is off the ground. Starting with this spike and with the help of a spirit level, you should now adjust the spikes so the speakers do not wobble and are not at an angle. Try to get the speakers to the same height, if at all possible.

The Palladium Series loudspeakers have a phenomenal frequency response and superb dynamics, so playing large orchestral or rock music will be an awesome experience, but may not necessarily be the best guide in setting up the speakers. Your listening tests should be performed with a wide range of music, including unac- companied vocal and solo instrumental recordings with as little processing on the source as possible. A natural solo cello recording will reveal much about the bass characteristics of your room and positioning. The best position will yield smooth, extended bass without boom or smear.

Stridency in the upper section caused by underdamped rooms can be compensated for by hanging drapes or pictures on the walls to dampen reverberant walls; increasing the amount of soft furnishings will also help to eliminate high frequency “ringing”.

Room resonances are often structural. In such circumstances, good placement will minimize but not eliminate these resonances.

Apparent height is critical. The speakers have controlled directivity. Phase response anomalies are kept to vanishingly low levels by reducing the distance between the midrange and tweeter horns to the absolute minimum; nevertheless, if you are in the wrong seat, it may happen that the sound stage is not perfectly inte- grated. One remedy is to tilt the speaker slightly (if necessary by using a combination of long and short spikes) to aim the midrange driver at the listener’s ear to yield best driver integration. Take your time with this—the effects on some music may be small and quite startling on others.

Phase

Phase is not a matter of preference. Out-of-phase effects manifest themselves as poorly defined bass, poor stereo with very vague localization of instruments and voice, and generally fuzzy, ill-defined sound. A single- wired out of phase system is easy to detect; a bi-amped system with one element connected out of phase can be nearly impossible to track down. If you find that there are problems with the system that no amount of experimentation can cure, check all the loudspeaker and amplifier wiring carefully. If you have connected your speakers strictly in accordance with this manual, no phase problems will arise.

Conclusion

All the advice above will help you get the most out of these superb loudspeakers, but in the final analysis you should do what your ears tell you is right—you are, after all, the final arbiter of your system.

Happy listening!

Page 12

Final Connections

Now, connect the loudspeakers to the amplifier/s using the diagrams on pages 8-11 to help you.

You are now ready to enjoy your music!

Page 13

Page 7
Image 7
Klipsch P-38F Finalizing the Assembly Final Adjustments, Dressing the Cables, Leveling the Loudspeakers, Final Connections

P-17B, P-27C, P-38F, P-27S, P-37F specifications

Klipsch, renowned for its commitment to audio excellence, offers a range of high-performance speakers that cater to audiophiles and cinephiles alike. Among these, the P-17B, P-38F, P-37F, P-27C, and P-27S stand out, each designed with unique features and cutting-edge technologies.

The Klipsch P-17B is a compact bookshelf speaker that packs a punch. With its Tractrix Horn-loaded tweeter, it delivers crisp and detailed high frequencies, making it a perfect choice for music lovers. Its 5.25-inch woofer provides deep bass response, ensuring that every note is heard. The speaker's minimalist design, combined with premium materials, ensures it blends seamlessly into any setting.

Moving up, the P-38F is a powerful floorstanding speaker that features dual 8-inch woofers, delivering enhanced bass performance and dynamic range. The P-38F utilizes Klipsch’s exclusive LTS tweeter, which minimizes distortion and ensures clear, detailed sound reproduction. Additionally, the Tractrix port design reduces turbulence, allowing for tight and accurate bass responses, making it ideal for home theater setups.

The P-37F also belongs to the floorstanding category, offering a slightly different sound profile. Its three-way design incorporates a 6.5-inch midrange driver for improved vocal clarity and a seamless transition between the highs and lows. The combination of dual 8-inch woofers and a Tractrix-loaded tweeter results in a wide soundstage and impressive imaging, making it an excellent choice for both music and movies.

For center channel performance, the P-27C is a standout. It features dual 5.25-inch woofers, providing powerful dialogue intelligibility and clarity in movie soundtracks. The Tractrix Horn technology enhances high-frequency performance, ensuring speech remains clear and engaging, which is crucial for an immersive home theater experience.

Lastly, the P-27S serves as a satellite speaker ideal for surround sound setups. Its compact design, featuring a 4-inch woofer and a Tractrix Horn tweeter, delivers remarkable sound quality without taking up much space. Perfect for mounting on walls or placing on shelves, the P-27S completes a multi-channel system with rich, detailed audio across all frequencies.

Overall, Klipsch's P series speakers, including the P-17B, P-38F, P-37F, P-27C, and P-27S, combine innovative technologies and aesthetic design to create a rich audio experience tailored for any environment, making them an excellent choice for anyone looking to elevate their sound.