![Bond in accordance with national and local codes.](/images/new-backgrounds/41421/4142117x1.webp)
Heater (models may vary)
Heater Electrical Cord
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Wiring Harness |
|
|
| |
Bond in accordance with national and local codes. |
|
|
|
| Pump Electrical Cord | ||||||||||||||||
Open bonding lugs are located at the top of the | Junction Box |
|
|
| |||||||||||||||||
junction box. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
120/240 VAC |
|
|
|
|
| Control |
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
| Source |
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
N |
| L1 | L2 | Typical Wiring Connection for North America | |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| Breaker Box |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| Typical |
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| * Connections to be Made |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| Circuit Breaker |
| at the Circuit Breaker | Wire | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| with GFCI |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| *L2 |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Connector | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 240 V |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Ground | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| 120 V |
|
|
|
|
|
|
|
|
|
|
| *L1 |
|
| ||||||
|
|
|
|
|
|
|
|
|
| (Green with | |||||||||||
|
| 120 V |
|
|
|
|
| No Connection | Blue (L1) |
| Yellow Stripes) | ||||||||||
|
|
|
|
|
|
| 240 V |
|
|
| (Load Neutral) |
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| * Line Neutral |
|
|
|
|
| From | ||
|
|
| S/N |
|
|
|
|
|
| ||||||||||||
|
|
|
|
| (White Curly |
|
|
|
|
| Control | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| Wire) |
|
|
|
|
| Brown (L2) | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Neutral Bus |
|
|
|
|
|
|
|
|
| * Equipment Ground | Field Wiring |
|
| Wire Connectors | |||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (From Junction Box | Electrician to provide suitable | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
(In Breaker Box) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| to GFCI Breaker) | strain relief cable. | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8. Make Electrical Connections
NOTE: The product model number is printed on a label on the pump side of the whirlpool bath. This label also identifies the electrical rating of the product. All whirlpools come equipped with a wiring junction box and are designed to operate between 208 VAC and 240 VAC at either 50 Hz or 60 Hz.
WARNING: Risk of electrical shock. Make sure the power has been disconnected before performing the following procedures. Refer to the “Important Information” section.
WARNING: Risk of electrical shock. To reduce the risk of electrical shock, connect the pump to a properly grounded
IMPORTANT! The load neutral is not used. There should be no connection to the load neutral terminal on the
The whirlpool bath control and system have been
Connect service to the junction box. The junction box contains blue, brown, and green with a yellow stripe colored wires.
Follow local electrical codes. Bond in accordance with national and local codes.
A wiring harness has been
NOTE: Your wiring harness included an antenna for the optional remote control. Do not alter or damage this antenna during installation.
Kohler Co. | 9 |