Manuals / Lantronix / Computer Equipment / Switch

Lantronix 4092A IRIG-B manual Index, R replacing

Models: 4092A IRIG-B

1 34

Download 34 pages 35.18 Kb

Page 34

Image 34

connecting 5

operational problems verifying 21

output connectors 3 LEDs 3

output signals connecting 5 troubleshooting 18

packing instructions 23 panels

front 3 rear 3

ports Command-And-Response 11 Ethernet 11

power connecting 5 connector 3 LED 3 specifications 25

power supplies configuring for dual 19 replacing 20 replacing fuses in 21

R replacing

a fuse 21

power supplies 20

safety instructions 5 setting autoswitch mode 9 shipping

information 23

software version, checking 14 specifications

electrical 25 environment 26 physical 26

status, checking 11 subnet mask, assigning 6 symbols 1

earth 1 fuse 1 LAN port 1

system status, checking 11

troubleshooting input problems 17 output problems 18

typographic conventions 2

unpacking the 4092A 5

warning 1 warning symbol 1 warranty information 23

Xport

Ethernet to RS-232 converter 6 user manual 7

Index

Page 34

Image 34

Lantronix 4092A IRIG-B manual Index, R replacing

Contents

4775 Walnut Street Suite 1B Boulder, CO TSC 4092A IRIG-B Autosense Fault SwitchOperations and Maintenance Manual Phone 303Date RevisionDescription Approved4 Troubleshooting the 4092A Contents2 Installing and Setting Up the 4092A 5 Warranty and Shipping InformationA.3 Electrical Specifications A.3.1 Environment Specifications Glossary IndexA.4 Physical Specifications 1 Introduction 1.1 SymbolsFIRST READ THIS MANUAL THOROUGHLY 1.2 About This Manual 1.2.1 Conventions1.3 4092A Overview Figure 1 Front panel1 Introduction 2.1 Safety Information 2 Installing and Setting Up the 4092A2.2 Installing the 4092A To set up the 4092A 2.3 Assigning a Static IP AddressYou can also assign the IP address using Telnet To select the active input channel from the front panel To assign the static IP address using Telnet2.4 Selecting the Active Input Channel To select the active input channel remotelyTo set the 4092A to autoswitch mode from the front panel 2.5 Setting the 4092A to Autoswitch Mode2.6 Cleaning To set the 4092A to autoswitch mode remotely2 Installing and Setting Up the 4092A 3 Monitoring the 4092A 3.1 Accessing the System3.2.1 Checking Status and Alarms 3.2 Checking System InformationBit position Table 1 Status or alarm binary codesStatus or alarm Bit value and descriptionTable 2 Example Telnet session Command sent4092A response To check the software version 3.2.2 Checking Model Number and Software VersionTo check the TSC model number Command sent3.3 Understanding Alarm Output 3 Monitoring the 4092A 4 Troubleshooting the 4092A 4.1 Troubleshooting Input Problems4.3 Troubleshooting Power Supply Problems 4.2 Troubleshooting Output Problems4 Troubleshooting the 4092A 4.5 Configuring for Dual Power Supplies 4.4 Configuring for Input Signal and ImpedanceTo change the jumper settings 4.6 Replacing Power Supplies To change the jumper setting4.7 Replacing Fuses 4.8 Verifying Operational ProblemsTo replace a power supply To replace a fuse4 Troubleshooting the 4092A 5.2 Shipping Information 5 Warranty and Shipping Information5.1 Warranty Information 5.2.1 Packing Instructions5 Warranty and Shipping Information Table 3 Electrical specifications Appendix A SpecificationsA.3 Electrical Specifications SpecificationA.4 Physical Specifications A.3.1 Environment SpecificationsGlossary Glossary Numerics Index4092A Operations and Maintenance Manual C cablesIndex R replacing