Manuals / Lantronix / Computer Equipment / Switch

Lantronix 4092A IRIG-B manual Introduction, Symbols, First Read This Manual Thoroughly

Models: 4092A IRIG-B

1 34

Download 34 pages 35.18 Kb

Page 5

Image 5

1: Introduction

Note

FIRST READ THIS MANUAL THOROUGHLY.

This is especially true for the sections regarding Safety and Operation.

1.1 Symbols

These symbols (icons) appear throughout the manual as well as on the unit itself.

Symbol Definition

This symbol means the following information is a note that gives you important

Note information that may affect how you use the 4092A.

Caution, refer to manual. Read all instructions in this manual before using this product.

Caution - Risk of electrical shock

Fuse symbol.

LAN port, network. DO NOT CONNECT TO TELECOM CONNECTIONS

THAT CARRY HAZARDOUS VOLTAGES.

Chassis ground.

CE marking attesting compliance with applicable European Directives.

Earth terminal symbol: used to indicate an earth ground connection to chassis.

4092A Operations and Maintenance Manual

Page 5

Image 5

Lantronix 4092A IRIG-B manual Introduction, Symbols, First Read This Manual Thoroughly

Contents

Operations and Maintenance Manual TSC 4092A IRIG-B Autosense Fault Switch4775 Walnut Street Suite 1B Boulder, CO Phone 303Description RevisionDate Approved2 Installing and Setting Up the 4092A Contents4 Troubleshooting the 4092A 5 Warranty and Shipping InformationA.4 Physical Specifications Glossary IndexA.3 Electrical Specifications A.3.1 Environment Specifications FIRST READ THIS MANUAL THOROUGHLY 1.1 Symbols1 Introduction 1.2.1 Conventions 1.2 About This ManualFigure 1 Front panel 1.3 4092A Overview1 Introduction 2.2 Installing the 4092A 2 Installing and Setting Up the 4092A2.1 Safety Information 2.3 Assigning a Static IP Address To set up the 4092AYou can also assign the IP address using Telnet 2.4 Selecting the Active Input Channel To assign the static IP address using TelnetTo select the active input channel from the front panel To select the active input channel remotely2.6 Cleaning 2.5 Setting the 4092A to Autoswitch ModeTo set the 4092A to autoswitch mode from the front panel To set the 4092A to autoswitch mode remotely2 Installing and Setting Up the 4092A 3.2.1 Checking Status and Alarms 3.1 Accessing the System3 Monitoring the 4092A 3.2 Checking System InformationStatus or alarm Table 1 Status or alarm binary codesBit position Bit value and description4092A response Command sentTable 2 Example Telnet session To check the TSC model number 3.2.2 Checking Model Number and Software VersionTo check the software version Command sent3.3 Understanding Alarm Output 3 Monitoring the 4092A 4.1 Troubleshooting Input Problems 4 Troubleshooting the 4092A4 Troubleshooting the 4092A 4.2 Troubleshooting Output Problems4.3 Troubleshooting Power Supply Problems To change the jumper settings 4.4 Configuring for Input Signal and Impedance4.5 Configuring for Dual Power Supplies To change the jumper setting 4.6 Replacing Power SuppliesTo replace a power supply 4.8 Verifying Operational Problems4.7 Replacing Fuses To replace a fuse4 Troubleshooting the 4092A 5.1 Warranty Information 5 Warranty and Shipping Information5.2 Shipping Information 5.2.1 Packing Instructions5 Warranty and Shipping Information A.3 Electrical Specifications Appendix A SpecificationsTable 3 Electrical specifications SpecificationA.3.1 Environment Specifications A.4 Physical SpecificationsGlossary Glossary 4092A Operations and Maintenance Manual IndexNumerics C cablesR replacing Index