32 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Step 9. REMOVING AND INSTALLING THE

GLASS DOOR

Air Shutter Adjustment Guidelines:
Amount of
Primary Air
Flame
Color
Air Shutter
Adjustment
If air shutter is
closed too far Flame will
be orange Air shutter
gap should be
increased
If air shutter is
open too far Flame will
be blue Air shutter
gap should be
decreased
Air Shutter Adjustment Guidelines
• Ifthereissmokeorsootpresent,rstcheck
the log set positioning to ensure that the
flames are not impinging on any of the logs.
If the log set is properly positioned and a
sooting condition still exists, then the air
shutter opening should be increased.
• Themoreoffsetsintheventsystem,thelarger
the air shutter opening will need to be.
• Anapplianceoperatedwith theairshutter
opened too far, may have flames that appear
blue and transparent. These weak, blue and
transparent flames are termed anemic.
• Propanemodelsmayexhibitameswhich
candle or appear stringy. If this is present
and persists, adjust the air shutter to a more
closed position, then operate the appliance
for a few more minutes to ensure that the
flame normalizes and the flames do not
appear sooty.
The following chart is provided to aid you in
achieving the correct air shutter adjustment
for your installation.

Figure 49

Step 10. BURNER ADJUSTMENTS

Flame Appearance and sooting

Proper flame appearance is a flame which is
blue at the base and becomes yellowish-orange
in the body of the flame.
2. Pull the latches forward and down to release
them from the door channel.
3. Pull the bottom of the door out a few inches
and grasp it on the right and left. Gently lift
to release the door from its channel above
the door. Pull the door forward.
4. Retrieve the glass door. Visually inspect the
gasket on the backside of the frame. Gasket
surface must be clean, free of irregularities
and seated firmly.
5. Inspect the gasket for defects. Insure it is
properly located. Make sure the bead is not
rolled up into the channel at the top of the
door, but remains flat against the top of the
glass (see Figure 49).
6. Position the door in front of the firebox
opening with the bottom of the door held
away from the fireplace (Figure 49). Hook
the top flange of the door frame over the top
of the firebox frame.
7. Let the bottom of the door frame swing
gently in towards the fireplace ensuring
that the gasket seats evenly as the door
frame draws shut. Fasten the two latches
located underneath the firebox floor to the
door's vee-flange. Close both the latches
securely.
8. Install the hood. Note the location of the three
clips inside the top air channel above the door.
The clips are equally spaced on the top surface
of the air channel opening. Use a screwdriver
to open the clips slightly if needed. Engage
the back edge of the eyebrow into the clips
to secure.
Door
Assembly
Gas Line Access Panel Bottom Panel
Blower Access
Plate
Note: When installing the glass door, ensure the
spacing on both sides is even and equal.

Only doors certified with the appliance

shall be used.

Seules des portes certifiées pour cet

appareil doivent être utilisées.

CAUTION: DO NOT abuse glass door by

striking or slamming shut.

1. To access the glass door securing latches,
first open the lower control compartment
door (Figure 49) by lifting and pulling the
bottom panel forward.
WARNING
• Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass. •Handlethisglasswithextremecare! Glass is susceptible to damage – Do not scratch or handle roughly while reinstall-ing the glass door frame.•Theglassdoor(s)ofthisappli-ance must only be replaced as a complete unit as provided by the manufacturer. Do not attempt to replace broken, cracked or chipped glass sepa-rately. • Do not attempt to touch the front enclosure glass with your hands while the fireplace is in use.
WARNING
Do not operate appliance with the glass front removed, cracked or broken.
AVERTISSEMENT
Ne pas utiliser l'appareil si le panneau frontal en verre n'est pas en place, est craqué ou brisé.
When the appliance is first lit, the entire flame
may be blue and will gradually turn yellowish-
orange during the first 15 minutes of operation. If
the flame remains blue, or if the flame is orange
with evidence of sooting (black tip), the air shut-
ter opening may need to be adjusted.
If the air shutter opening is closed too far,
sooting may develop. Sooting is indicated by
black puffs developing at the tips of very long
orange flames. Sooting results in black deposits
forming on the logs, appliance inside surfaces
and on exterior surfaces adjacent to the vent
termination.
Sooting is caused by incomplete combustion
in the flames and lack of combustion air enter-
ing the air shutter opening. To achieve a warm
yellowish-orange flame with an orange body
that does not soot, the shutter opening must be
adjusted between these two extremes.