Fireplace Specifications
Cat. No. H3428
Model:
Description: Merit Plus Electric Fireplace - 27”
Shipping Weight: 78 lb.'s (35 KG) Packaging:
34 1/2” x 14” x 34”
(876 mm x 356 mm x 864 mm)
14.1cu. ft. Power Requirements:
(120 Volt, 60 Hz.)
Rated Wattage - 1600 Watts Amperage - 15 Amps
Blower CFM: 83 CFM
(120 V): 5,461 BTU/HR
Minimum Clearances to Combustibles
Sides: | 25.5 mm - 1 inch |
Floor: | 25.5 mm - 1 inch |
Top: | 25.5 mm - 1 inch |
Mantel Clearance: Combustible and
Hearth Protection: A hearth is not mandatory, but may be used for aesthetic purposes. Secure the hearth extension to the floor to prevent possible shifting. Do not block the airflow beneath the appliance (read the following WARNING).
WARNING: This appliance is mounted on rubber feet to ensure adequate air circula- tion beneath fireplace. Do not block airflow at the bottom air intakes.
IMPORTANT: Cold climate installation recom-
mendation: when installing this fireplace against a
WARNING: To prevent contact with sagging or loose insula- tion, the appliance must not be installed against vapor bar- riers or exposed insulation. Localized overheating could occur and a fire could result. Insulation and a vapor barrier should be placed a minimum of 1 inch from the appliance.
PRE-INSTALLATION
Before You Start
Check appliance for any concealed damage.
Detailed Installation Steps
1.Complete the framing opening to the di- mensions specified in Figure 2 or assemble mantel.
2.A dedicated circuit is not required. Use an outlet that is protected by a ground fault circuit interrupter where required by electrical code.
3.Plug the fireplace into receptacle.
4.Slide the fireplace into place in framed/fin- ished opening or into mantel.
5.Perform a function test. See Operating Instructions and Remote Control Operation on Page 6.
WARNING: Electrical wiring must comply with local build- ing codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to individuals.
WARNING: Do not use this fire- place if any part of it has been underwater. Immediately call a qualified service technician to inspect the fireplace and replace any part of the elec- trical system which has been under water.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
FINAL FINISHING
Materials such as brick and tile can be extended down to the top of the fireplace. Do not extend down, covering the outlet or glass enclosure panel (optional kit).
There are a wide variety of “finished looks” for these fireplaces, from formal wall decor with elaborate mantels to rustic wood paneling or warm brick facings.
Mantel Cabinet
An optional mantel cabinet kit is available from your dealer (see Page 9). This option gives the appliance an attractive finished look.
Hearth
An aesthetically pleasing fireplace hearth can be installed, if desired.
BREAK-IN PERIOD:
During the first few initial uses of this heater, there may be a release of a slight, harmless odor. This odor is a normal occurrence caused by the initial heating of the internal heating elements and should not reoccur.
Existing fireplace installation
Thoroughly clean out the existing fireplace and hearth area.
Plan the power supply. If an existing grounded outlet is near the fireplace, the cord can run along the front of the fireplace. If the cord is not long enough to reach the outlet, a grounded exten- sion cord minimum AWG No. 14 and rated to a minimum of 1875 watts, may be used.
If you plan to cut or drill a hole in the existing fireplace for wiring, it is best to hire a profes- sional to do this step in order to prevent personal injury. To reduce the risk of fire, do not run the power cord under rugs, carpets, etc. Arrange the power supply cord away from high traffic areas where it may pose a tripping hazard.
