Following are important instructions and information concerning the exhaust requirements for your dryer.
!Important Warning: To reduce the risk of fire, combustion, or accumulation of combustible gases, DO NOT exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil ducting.
|
| Weather Hood |
|
|
|
|
| Number of 90° | Maximum length of 4” | Maximum length of 4” | |||||||
|
|
|
|
| Type |
|
|
|
|
| Elbows | (10.2 cm) diameter rigid | (10.2 cm) diameter | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| metal duct | flexible metal duct |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Recommended |
|
|
|
|
| 0 | 65 feet (19.8 m) | 45 feet (13.7 m) | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 55 feet (16.8 m) | 35 feet (10.7 m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 | 47 feet (14.3 m) | 30 feet (9.1 m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | 36 feet (11.0 m) | 25 feet (7.6 m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | 28 feet (8.5 m) | 20 feet (6.1 m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| 4” |
| 4” |
|
| ||||||||||
|
|
|
|
|
|
|
|
| |||||||||
| (10.2 cm) | (10.2 cm) |
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Use Only for Short Run |
|
|
| |||||||||||||
|
|
| Installations |
|
|
|
|
| 0 | 55 feet (16.8 m) | 35 feet (10.7 m) | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 47 feet (14.3 m) | 27 feet (8.2 m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 | 41 feet (12.5 m) | 21 feet (6.4 m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | 30 feet (9.1 m) | 17 feet (5.2 m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | 22 feet (6.7 m) | 15 feet (4.5m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (6.35 cm) |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE : Deduct 6 feet (1.8 m) for each additional elbow.
It is not recommended to use more than 4 90° elbows.
1.Venting materials are not provided with the dryer and you should obtain the necessary venting materials locally. For example, the outer end of exhaust pipe must have a weather hood with hinged dampers to prevent
2.The exhaust duct must be four inches (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer.
3.Rigid metal duct is recommended. Do not install flexible duct in concealed spaces.
4.DO NOT use sheet metal screws on exhaust pipe joints or other fastening means which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape.
5.To maximize operating results, please observe the duct length limitations noted in the chart above.
2 0