Manuals / LG Electronics / Kitchen Appliance / Cooktop

LG Electronics LCE30845 service manual Terminal block and power cord assembly, Disassembly

Models: LCE30845

1 48

Download 48 pages 47.78 Kb

Page 35

Image 35

DISASSEMBLY

Terminal block and power cord assembly

1. Loose the two screws on the bottom plate

2. Loose the earth screw on the bottom plate

3.Loose the ring of conduit bracket with a hand to remove the power cord assembly.

LGE Internal Use Only	- 35 -	Copyright © 2007 LG Electronics. Inc. All right reserved.
		Only for training and service purposes

Page 35

Image 35

LG Electronics LCE30845 Terminal block and power cord assembly, Disassembly, Loose the two screws on the bottom plate

Contents

Internal Use Only Website http//biz.lgservice.comCeramic Glass Induction Cooktop MODEL LCE30845IMPORTANT NOTICE RADIO INTERFERENCE SAFETY PRECAUTIONSSAFETY PRECAUTIONS FORWARDWARNING Never use your appliance for warming or heating a room SAFETY PRECAUTIONSELECTRICAL SAFETY SAFETY PRECAUTIONSSAFETY PRECAUTIONS cont Never place combustible items on the cooktop SAFETY PRECAUTIONSSwitch off the Cooking Zones after use Do not use the cooktop to heat the roomAlways switch off the appliance before cleaning SAFETY PRECAUTIONSSAFETY DURING USE cont SAFETY WHEN CLEANINGSAVE THESE INSTRUCTIONS SAFETY PRECAUTIONSHOW TO AVOID DAMAGE TO THE APPLIANCE READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLYCopyright 2007 LG Electronics. Inc. All right reserved CONTENTSOnly for training and service purposes DESCRIPTION SPECIFICATIONSThe rated power consumption may vary according to pan size and type Read these instructions completely and carefully INSTALLATION INSTRUCTIONSNOTES TO INSTALLER READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCEIMPORTANT INSTALLATION INFORMATION INSTALLATION INSTRUCTIONSPREPARING THE INSTALLATION LOCATION Model INSTALLATION INSTRUCTIONSDIMENSIONS AND CLEARANCES Only for training and service purposesELECTRICAL REQUIREMENTS INSTALLATION INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS PROVIDING THE ELECTRICAL CONNECTIONObserve all governing codes and local ordinances INSTALLATION INSTRUCTIONSDisconnect the power supply Electrical ground is required on this applianceObserve all governing codes and local ordinances INSTALLATION INSTRUCTIONS4-WIRE GROUNDED JUNCTION BOX MODEL AND SERIAL NUMBER LOCATION INSTALLATION INSTRUCTIONSPreferred installation Alternative installation FINAL CHECKHOW INDUCTION COOKING WORKS INDUCTIONINDUCTION COOKING SELECTING COOKWAREFOR BEST RESULTS INDUCTIONAVOIDING SCRATCHES USE FLAT-BOTTOMED COOKWARECORRECT COOKWARE SELECTION AND PLACEMENTINDUCTION SELECTING THE PROPER PAN SIZEPROBLEM SOILS CLEANING AND CARECLEANING THE COOKTOP GENERAL CLEANINGPARTS AND FEATURES OF YOUR COOKTOP DESCRIPTION OF FEATURETOUCH CONTROL FEATURES DESCRIPTION OF FEATUREFIRST OPERATION OPERATING INSTRUCTIONSBEFORE USING THE COOKTOP SETTING THE CONTROLSTo turn off the cooking zone SETTING THE POWER LEVELTo adjust the power level OPERATING INSTRUCTIONSWARM POWER BOOSTACTIVATING POWER BOOST OPERATING INSTRUCTIONSFunction POWER LEVEL GUIDESetting OPERATING INSTRUCTIONSBRIDGE COOKING ZONES SETTING THE TIMERCANCELING THE TIMER OPERATING INSTRUCTIONSPOWER SHARING TIPS SETTING CHILD LOCKCANCELING CHILD LOCK POWER SHARINGLGE Internal Use Only ELECTRIC CIRCUIT DRAWINGOnly for training and service purposes Ceramic Glass Part DISASSEMBLYOnly for training and service purposes Burner assemblyDISASSEMBLY 1. Disconnect Top temp. sensor 2. Loose coil assemblyOnly for training and service purposes Controller assemblyDISASSEMBLY 2. Loose earth wire of left and right sideDISASSEMBLY IH module assemblyOnly for training and service purposes Power harness assemblyDISASSEMBLY 2. Take out the harness assembly1. Loose the two screws on the bottom plate Terminal block and power cord assemblyDISASSEMBLY Only for training and service purposes1. Cut out the staple with nipper Burner assembly leftDISASSEMBLY Only for training and service purposesDISASSEMBLY Burner assembly right2. Take out the key PCB hooked by key supporter Controller assembly key PCBDISASSEMBLY Only for training and service purposesDISASSEMBLY Controller assembly main PCB1. Loose a screw and push and lift the cover IH module assembly Induction boardDISASSEMBLY Only for training and service purposes4. Loose the four screws that fix the PCB to base DISASSEMBLYIH module assembly Induction board Only for training and service purposesOnly for training and service purposes IH module assembly filter boardIH module assembly fan DISASSEMBLYCeramic Glass TROUBLE SHOOTINGThe procedure of main functions No Power / Noheating is not TROUBLE SHOOTINGThe procedure of main functions IHInductionHob does not work TROUBLE SHOOTINGThe procedure of main functions Flashing HCopyright 2007 LG Electronics. Inc. All right reserved EXPLODED VIEWOnly for training and service purposes MODEL LCE30845330401 EXPLODED VIEW350121 WSZ002