LG Electronics LF-D7150 owner manual Before Operation

Before Operation

Volume Adjustment

•Turn VOLUME knob clockwise to increase the sound level, or counterclockwise to decrease it.

•Press VOLUME + to increase the sound level, or use VOLUME - to decrease it on the Remote Control.

Sound Quality Adjustment

• To activate stereo sound

Select a desired sound mode by using the EQ button on the front panel or the Remote Control.

Each time you press the button the setting changes in the display window as shown below.

FLAT	→ POP	→	CLASSIC
↑			↓
JAZZ	← DRAMA	←	ROCK

• Headphone Jack

Connect a stereo headphone plug (3.5mm) into the headphone jack.

The speakers are automatically disabled when you plug in headphones (not supplied).

MUTE

Press MUTE to turn off the sound, press again to restore. You can mute your unit in order to answer the telephone. The “” indicator flashes in the display window.

XDSS (Extreme Dynamic Sound System)

Press XDSS button repeatedly to reinforce treble and bass.

XDSS ON → XDSS OFF

MP3 Optimizer

This function is optimizes compressed MP3 file. It provides improvement to the bass sound. Each time you press MP3 OPT. the setting changes in the following order.

MP3-OPT ON t MP3-OPT OFF

XTS pro

Each time you press XTS pro the setting changes in the fol- lowing order.

XTS-P ON → XTS-P OFF

SPECTRUM Effect

Each time you press the DISP.MODE button repeatedly on the Remote Control, you can check the sprectrum change of 6 types in the display window.

DIMMER

This function dims the LED of the front panel by half in power-on status .

Press DIMMER once. The LED (Light-emitting diode) of front panel is turned off. If you press it once more, the display win- dow will be darken by half. To cancel, press the button again.

Setting the Clock

1 Press CLOCK.

(If the clock requires setting, press and hold CLOCK for more than 2 seconds.)

- The hours display begins to blink.

	Select a 24 hour cycle or 12 hour cycle by
2 pressing . bb/BB > on the front panel.
	(12HR)	or	(24HR)
	Press SET/CD[[ to confirm the selected hour
3 cycle.
	Use . bb/BB > on the front panel to set
4 the correct hours.
5	Press SET/CD[[.
	Use . bb/BB > on the front panel to set
6 the correct minutes.
7	Press SET/CD[[ and the correct time is shown
	on the display window.

ote

When the clock does not appear in the display window, follow as below.

-In case the clock is set, prese the CLOCK button. The clock will be shown in the display window for about 5 seconds.

-In case the clock is not set, the clock will be blinked in the display window for about 1 minute. Set the clock as above.

Sleep Timer Function

When the sleep timer is set, the unit automatically turns off after the specified time has elapsed.

1	To specify the time delay before the power is
	turned off, press SLEEP.
	In the display window you can see SLEEP 180 for
	about 5 seconds. This means that the system turns
	off automatically after 180 minutes.

2 Each time you press SLEEP the setting changes in the following order.

SLEEP 180 →150 → 120 →90→80→70 → 60→ 50 → 40 →

30 → 20 →10 → OFF→SLEEP 180...

3 To check the remaining time until the power is turned off.

While the sleep function is active press SLEEP briefly. The time remaining until the unit turns off is displayed for about 5 seconds.

ote

If you press SLEEP while the sleep time is displayed, the SLEEP time is reset.

To cancel Sleep Timer setting

If you wish to stop the function, press the SLEEP button repeatedly until “SLEEP 10 ” appears, and then press SLEEP once again after “SLEEP 10 ” shows on the display.

10