3 kitchen unit side panel
4 wall

Instructions for installation and modification

Dimensions

The external dimensions of the appliance can be seen on

fig. S and in the table below.

 

 

 

 

Gross capacity

External dimensions

[mm]

 

of appliance [l]

A

B

C D

E

F

(see type plate)

 

 

 

 

 

162(18..) 1250 600 631 614 644 1179

200(21..) 1447 600 631 614 644 1179

238(25..) 1644 600 631 614 644 1179

276(28..) 1841 600 631 614 644 1179

188(20..) 1250 660 683 662 704 1287

233(24..) 1447 660 683 662 704 1287

279(29..) 1644 660 683 662 704 1287

324(33..) 1841 660 683 662 704 1287

Installation instructions

- Do not install models without side-wall heating side-by- side with another refrigerator or freezer. This is important to prevent condensation and consequential damage from it.

- Models with side-wall heating are designed for side-by- side installation; they are designed for combination with a refrigerator.

Contact your dealer for more information.

-Attachment instructions are supplied in the accessories bag of the appliance with side-wall heating.

Changing over door hinges

The door hinges can be changed from one side to the other if required.

WWith the door open, lever out plinth panel 1 on the hinge side with a screwdriver and remove from front.

-Lever out cover 2 with a screwdriver. Close door.

-Unscrew screw M5 3.

WPull hinge component 4 with hinge pin 5 out from un- derneath and remove.

WOpen door, lift out at bottom and remove; do not lose the spacer 6.

WTransfer all hinge components onto the other side:

-Lever out covers 8 with a screwdriver at the front and remove at an angle from below. Remove hinge pin 7 and insert on the opposite side. Use the hexagon socket on the open-ended spanner provided (spanner width 5). Fit covers 8 again: insert at rear and click into place at front.

-Bottom: Using a screwdriver, remove the spacer 9 and replace on the other side.

WRe-attach the door:

-Remove plugs bo from the door mounting points and replace on the other side.

-Suspend door with spacer 6 in hinge pin 7, close door.

-Rotate hinge component 4 by 180°, remove hinge pin 5, turn by 180° and replace. Mount both parts in the hinge bp: slide the pin into the door mounting through the hinge, tilt in the hinge component, slide up and attach with screw 3.

WAlign the door flush with the body of the appliance using the slot on the hinge bp, then tighten screw 3.

WAttach the plinth panel 1 and click into place by press- ing.

WWith the door open, insert the cover 2 in the plinth panel at the front and click into place at the back.

WTransfer* door handle bl and plugs bm: With the door open, carefully lift out the pressure plates* bn at the front and slide away; unscrew handle.

Re-assemble in reverse order: replace the pressure plates and click into position.

Insertion into row of kitchen units

Fig. U. 600 mm appliances can be installed in a row of kitchen units. To adapt the height of the appliance to the surrounding furniture a top unit 1 can be added.

A gap of at least 50 mm depth must be provided behind and along the entire width of this unit so as to ensure sufficient ventilation. The area of ventilation underneath the ceiling should be at least 300 cm2. The greater the area the more economically the appliance will run.

WWhen installing with standard kitchen units (max. depth 580 mm) and decor panels of max. 2 mm thickness, the appliance can be set up right next to the kitchen unit.

The door protrudes 34 mm from the side of the kitchen unit and 51 mm at the front. This enables it to be opened and closed without difficulty.

WWhen setting up the appliance next to a wall 4, a mini- mum distance of 36 mm must be provided on the hinge side between the appliance and the wall (for the handle when the door is open).

1 top unit

2 refrigerator/freezer

Notes on assembling decor panels

with white appliances of width B = 600 mm and height A = 1841 mm:

Decor panel and frames can be attached to the door of your appliance to match or contrast it to the existing kitchen colour scheme.

The panels are available from your kitchen furniture supplier. The frames can be fitted later and are available from your dealer.

If you wish to fit the decor panels yourself, you will need a drill or a rechargeable screwdriver to pre-drill the retain- ing holes. The door handles are to be replaced by the rigid handles included in the decor frame retrofit kit.

For further instructions and dimensions see the installation instructions included in the retrofit kit.

GN..3

20

Page 10
Image 10
Liebherr 7082 308-00 manual Instructions for installation and modification, Dimensions, Changing over door hinges