IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
IMPORTANTES!
NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION.
1.Before proceeding, familiarize yourself with the parts of the
items described in the Component List.
2. Locate the left and right FRONT COVER (9 &10). Using two | 9 | |
PHILLIPS PAN HEAD POINTED SCREWS (3), mount the LEFT FRONT |
| |
COVER (9) to the FRAME (A). Attach the RIGHT FRONT COVER (10) |
| |
to the FRAME in the same manner using two PHILLIPS PAN HEAD | 3 | |
POINTED SCREWS (3). Secure the tops of the FRONT COVERS | ||
A | ||
together using two PHILLIPS PAN HEAD POINTED SCREWS (3). | ||
10 | ||
CAUTION: Do not overtighten the PHILLIPS PAN HEAD POINTED | ||
| ||
SCREWS (3). |
| |
3. Locate the RIGHT USER ARM (12). Snap the |
| |
(2PA) located at the bottom of the RIGHT USER ARM into the 2- |
| |
PIN CONNECTOR (2PB) positioned at the top of the RIGHT ROCKER |
| |
ARM (B). Feed the connectors and excess cable up into the | 12 | |
RIGHT USER ARM. Secure the RIGHT USER ARM to the RIGHT |
| |
ROCKER ARM using three HEX SOCKET HEAD CAP SCREWS (1) and |
| |
three INTERNAL TOOTH LOCK WASHERS (18). Repeat the procedure | 11 | |
for the LEFT USER ARM (11) and LEFT ROCKER ARM (C). Tighten | 18 | |
all screws securely. | ||
1 | ||
CAUTION: Be careful not to pinch the WIRE HARNESSES when |
| |
assembling the USER ARMS (11 &12) to the ROCKER ARMS (B & | 2PA | |
C). | ||
|
3
4.Detach and unwrap the WIRE HARNESS (E) (16P, 4P) located at the top of the MONOCOLUMN (F). Holding the CONSOLE SUPPORT ASSEMBLY (7) with the handgrips facing upward, feed the WIRE HARNESS up through the neck and out the top access hole.
Carefully lower the CONSOLE SUPPORT ASSEMBLY into the
MONOCOLUMN.
CAUTION: Be careful not to pinch the WIRE HARNESSES (E) when assembling the CONSOLE SUPPORT ASSEMBLY (7) to the
MONOCOLUMN (F).
5.Using two HEX SOCKET HEAD CAP SCREWS (1) and two FLAT
WASHERS (8), secure the CONSOLE SUPPORT ASSEMBLY (7) to the MONOCOLUMN (F). Tighten the SCREWS securely.
6.Insert the GROMMETS (20) into the four holes on the CONSOLE SUPPORT ASSEMBLY. Locate the ACCESSORY TRAY (17). Align the ACCESSORY TRAY with the four holes on the CONSOLE SUPPORT
ASSEMBLY. Using four PHILLIPS PAN HEAD POINTED SCREWS (3), secure the ACCESSORY TRAY to the CONSOLE SUPPORT ASSEMBLY
as shown. Tighten the SCREWS securely.
CAUTION: Do not overtighten the PHILLIPS PAN HEAD POINTED SCREWS (3).
2PB
C
B
| 4P |
| 16P |
21 | 4 |
|
19
23
2 | 3 |
| |
7 | 17 |
E | 20 |
1 |
|
22
7. Remove the adhesive back and install the PAD (23). Install | 8 |
the CUP (22). |
|
F
5
