Lightolier 1102TH2R Fig. F, Fig. J, Fig. H, Instruction For Ballast Replacement, Fig. K, B0600

Models: 1102T Series 1102TH2R

1 2
Download 2 pages 38.86 Kb
Page 2
Image 2
INSTRUCTION SHEET NO.

INSTRUCTION SHEET NO.

IS:1102TH1R

B0600

Page 2 of 2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal code specifications. To assure full compliance with codes and regulations, check with your local electrical inspector before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

4.ATTACH MOUNTING RING (FIG. F & G)

Push MOUNTING RING into opening until FLANGE sits against ceiling. Slide MOUNTING STRIOPS down to trap ceiling thickness and then bend up to secure.

FIG. F

FIG. G

MOUNTING CLIP

 

 

 

MOUNTING RING

 

 

 

 

FLANGE

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

PULL-THRU (FIG. H)

 

 

 

 

 

 

 

 

6.

PUSH-UP (FIG. I)

 

 

 

 

7.

SNAP-IN (FIG. J)

 

 

 

 

 

SEE SEPRATE REFLECTOR TRIM

 

FIG. I

 

 

 

INSTRUCTION SHEET

 

 

FIG. J

 

 

FIG. H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTRUCTION FOR BALLAST REPLACEMENT

BALLAST REPLACEMENT

1.TURN POWER OFF

2.Remove REFLECTOR TRIM from ceiling (see REFLECTOR TRIM instructions).

3.Remove BALLAST ASSEMBLY by lifting SPRING on top of J-BOX and pull BALLAST outward. (Fig. K)

4.Disconnect all wiring.

5.Remove BALLAST ASSEMBLY from J-BOX by pulling SPRING upward.

6.Remove BALLAST ASSEMBLY through ceiling opening.

7.Disassemble (2) locknuts which held BALLAST to J-BOX COVER. (Notice orientation of two MOUNTING FINGERS on bottom and one MOUNTING TAB on top of COVER. They are on the opposite (inside) surface of the door from which BALLAST is mounted.)

8.Replace old BALLAST with new BALLAST and lock with locknuts.

9.Reassemble new BALLAST ASSEMBLY to J-BOX by replacing TABS into SLOTS on frame, snap onto SPRING.

10.Rewire Fixture. (SEE WIRING DIAGRAM ON BALLAST LABEL.)

 

 

 

 

 

 

 

BALLAST

 

 

 

 

 

 

 

ASSEMBLY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SPRING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J-BOX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J-BOX

 

 

 

 

 

 

 

 

 

 

 

BRACKET

 

 

 

 

 

 

 

 

 

 

 

 

 

BALLAST

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J-BOX

 

 

 

 

 

 

 

 

 

 

COVER

 

 

 

 

 

 

 

 

 

 

 

TABS (2)

 

 

 

 

 

 

 

 

 

 

SLOTS

 

 

 

 

 

 

 

IN J-BOX

 

 

 

 

COVER

 

 

 

 

FIG. K

 

 

 

 

 

LIGHTOLIER a GENLYTE THOMAS company

631 Airport Road,Fall River MA 02720

© 2000

 

Page 2
Image 2
Lightolier 1102TH2R Fig. F, Fig. J, Fig. H, Instruction For Ballast Replacement, Fig. K, Page 2 of, Instruction Sheet No