Lightolier IS:6440 Assemble Mounting Clips to Track, Installing Track Into Housings in Patterns

INSTALLATION OF BASIC OR ADVENT LYTESPAN TRACK INTO HOUSINGS

Each straiaht run of track is started with an lNDIVi DUAL TRACK UNIT and continued with JOINER TRACK UNITS.

To cut track, see Instruction Sheets supplied with Track. 1S:6020 or 1S:6121.

ASSEMBLE MOUNTING CLIPS TO TRACK	ALLEN HEAD SCREW
	7/8”	Long for Basic	Track,
1. Prepare MOUNTING CLIP ASSEMBLIES as shown.	1[2’(	Long for Advent Track
	—CAPTIVE		NUT

1S:6440

Paae------3 of z

I

2.Remove DEAD END COVER from INDIVIDUAL TRACK UNITS, see Fig. 8. Insert MOUNTING CLIPS into end of each track unit and slide

along track until ends of clips engage alignment

holes. Check that allen head screw lines up with B hole in track.

INSTALLING TRACK INTO A SINGLE HOUSING

1.Unscrew BOTTOM COVER and remove KO from top plate on LIVE END. Reinsert DEAD END COVER into other end of track.

NOTE: See Instruction Sheet supplied with track

for additional instructions on installing supply leads into LIVE END.

SPACER.Useonly

for Basic Track

MOUNTINGCLIP

MOUNTINGCLIP

ASSEMBLY

HOUSING

WALL MOUNTING

KIT

N

CH

FIG. 7

INDIVIDUAL TRACK

UNIT (Basic)

2.Pass supply leads through openings in LIVE END observing polarity. Insert track into HOUSING and tighten screws in MOUNTING CLIPS with allen wrench to lock track in place.

3.Fasten BOTTOM COVER to LIVE END. Connect SUPPLY LEADS to screw terminals as shown in track IS:6020 or IS:6121.

1.		MOUNTING	CLIP	ASSEMBLY
...	~ALLEN	WRENCH	-	‘

CAPTIVE NUT

BOTTOM	COVER
INSTALLING TRACK INTO A STRAIGHT RUN OF HOUSINGS	,.
	,/ /-

1.Follow previous instructions except do not reinstall DEAD END COVER.

2.Remove END PLATE from HOUSING. Insert JOINER TRACK into HOUSING, plug COUPLER

into INDIVIDUAL TRACK UNIT and tighten				INDIVIDUALTRACK
				UNIT(Bas[c)
screws in MOUNTING CLIPS with allen wrench,
Repeat for all JOINER TRACK UNITS in run.
3. Tighten	screw in	COUPLER(S).	Insert DEAD E?JD		/“
COVER	into end	of track run	and insert END		-“3
PLATE into end of HOUSING.				..’	1
					{
				~COUPLER	~

INSTALLING TRACK INTO HOUSINGS IN PATTERNS

			c1		ENDPLATE
HOUSING			,.- ..’
	Q’		~		‘~jjf%ij~;jR
			.:::$J		TrackUnN)
		@-	~		JOINERTRACK
A					UNIT(Basic)
,//		MOUNTINGCLIP
		ASSEMBLY
#/&;:H
SCREW				FIG. 10
*	.k			r	INDIVIDUAL TRACK
	-.	-	..-		UNIT (Basic)

1. Remove

LIVE ENDS from all INDIVIDUAL

TRACK

LIVE END x

-

‘=’

.

UNITS.

(discard)

e

. --- :>-\-

LOOSEN

SCREW

c

FIG. 11

TO REMOVE

2. Lay out the track

TRACK ORIENTATION

per

the

layout ot

tne

Corner

“T” Intersection

“X” Intersection

HOUSINGS

following

the

track

orientation

shown in Fig. 12. Note

that

each

straight

run

of

track

consists

An

M.

‘f:~

““’f’i~;:f’s”

‘“;

of

an INDIVIDUAL

Plus

JOINERS.

R[ghtof

Left of

R

Track = R

Track = L

5

~j

~~

L]R+

FIG. 12