Lightolier IS:T300 instruction sheet Relamping Trim Standard Model, Trim Adjustable pinhole Model

INSTRUCTION SHEET	IST:300
	09-01/Rev-03

INSTALLATION INSTRUCTIONS FOR MR-16/ES16 TRIM IN PRE-WIRED

INCANDESCENT 12V OR 120V MOUNTING FRAME

ATTENTION: Read and understand these instructions before installing fixture. This fixture is intended for installation in accordance with the National Electrical Code or Canadian Electrical Code (if applicable) and local regulations.To ensure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. Retain these instructions for maintenance reference.

Note: For the 50W IC frame-in kit

LAMP

SOCKET

Put down the lamp shield (included with the IC frame-in kit)

SHIELD

LAMP

onto the lamp. (Fig.1)

A. LAMP:

PINS

1.

MR16: Insert the pins of the lamp base into the socket.

FIG.1

LAMP

FIG.2

(Fig.2)

2.

ES16: Insert the pins of the lamp base into the socket.

LAMP

and rotate the lamp clockwise. (Fig.2A)

LAMP

3.

Turn the lamp under spring (if applicable). (Fig.3,4,5)

SPRING

CAUTION: Lamp manufacturer recommends that the

PROTECTIVE

protective glass be in place before energizing the

lamp. Insure that the lamp is fully cooled before

FIG.2A

GLASS

FIG.3

relamping.

B. TRIM: Standard (Model 305)

LAMP

1.

Push the trim into the housing. (Fig.6)

SPRING

2.

Aim the lamp beam at the desired angle if necessary.

(Fig.12)

C. TRIM: Adjustable pinhole (Model 308)

FIG.4

FIG.5

1.

Push the trim into the housing. (Fig.7)

2.

Gently rotate the trim to fit it to the ceiling.

3.

Aim the lamp beam at the desired angle if necessary.

Model 305

Model 308

(Fig.11)

D. TRIM: Glass (Model 322)

HOUSING

1.

Take the loop found at the end of the security cable

HOUSING

attached to the trim and secure by passing the loop

over either one of the screws found within the housing.

(Fig. 8)

2.

Push the trim into the housing. (Fig.8)

3.

Gently rotate the trim to fit it to the ceiling.

E.

TRIM: Adjustable elbow (Model 478)

TRIM

FIG.6

FIG.7

1.

Push the trim into the housing ,compressing the (2)

springs as shown. (Fig.9)

TRIM

F. TRIM: Wall Washer (Model 315)

1.

Push the trim into the housing and position the lamp

shield as shown. (Fig.10)

Model 322

Model 478

Model 315

2.

Push the trim into the housing and position the lamp

HOUSING

shield as shown. (Fig.10)

LOOP

HOUSING

Wall Washer:

1.

Position the fixture a minimum of 12” away from the

HOUSING

wall. (Fig.10)

2.

Adjust the angle of the beam towards the baffle by

SECURITY

using the frosted glass. (Fig.9)

SPRINGS

CABLE

WALL

Accent Lighting:

1.

Adjust the angle of the beam to the required position

TRIM

SHIELD

by using the clear glass.

G. ES16 TRIM: (Models 325, 330)

TRIM

FIG.9

FIG.10

1.

Install the spring tabs into the slots in the base.

FIG.8

(Fig.11)

2.

Insert the pins of the lamp base into the socket.

Model 325,330

and rotate the lamp clockwise. (Fig.2, 2A)

SPRING

3.

Push the trim into the housing. (Fig.12)

TABS

HOUSING

4.

Aim the lamp beam at the desired angle if necessary.

SLOTS

(Fig.12)

H. TRIM: Contour (Model 316)

1.

For added protection in shower application , install the

FIG.11

FIG.12

gasket for water-tightness (included). Gently fasten

TRIM

onto the trim. (Fig.13)

I.

MAINTENANCE of ALZAK® REFLECTORS OR

ALZAK® CONES: (if applicable)

GASKET

Note: Handle the reflector or the Alzak® cone with

clean gloves or plastic film to avoid fingerprints.

1.

Clean Alzak® surfaces with a clean soft cloth

TRIM

FIG.13

dampened in a mild detergent solution.

2.Rinse then wipe dry with a dry cloth or a paper towel. Avoid abrasives.