Manuals / Lincoln Electric / Kitchen Appliance / Water Dispenser

Lincoln Electric IM670-A Dimension Print, Fill Cap, A L11540, Cool Arc, 9.03, 9.10, 2.27 34.26

Models: IM670-A

1 26

Download 26 pages 35.1 Kb

Page 22

Image 22

FILL CAP

F-2

COOL ARC® 40

9.03

9.10

2.27

34.26

A

L11540

DIMENSION PRINT

NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number..

F-2

Page 22

Image 22

Lincoln Electric IM670-A manual Dimension Print, Fill Cap, A L11540, Cool Arc, 9.03, 9.10, 2.27 34.26

Contents

COOL ARC 40 STAND ALONE IM670-A Safety Depends on YouSales and Service through Subsidiaries and Distributors Worldwide WATER COOLERELECTRIC AND MAGNETIC FIELDS may be dangerous SAFETYFOR ENGINE powered equipment CALIFORNIA PROPOSITION 65 WARNINGSFUMES AND GASES can be dangerous ELECTRIC SHOCK can killARC RAYS can burn SAFETYWELDING and CUTTING SPARKS can cause fire or explosion iiiSAFETYFOR ELECTRICALLY powered equipment CYLINDER may explode if damagedMar. ʻ93 PRÉCAUTIONS DE SÛRETÉSAFETY COOL ARCThank You Section E TABLE OF CONTENTSPRODUCT DESCRIPTION Section FO OFF INSTALLATIONEXPLANATION OF SYMBOLS THAT APPEAR ON THIS EQUIPMENT TECHNICAL SPECIFICATIONS - COOL ARCRecommended Coolant SAFETY PRECAUTIONSINSTALLATION UNPLUG THE COOLER BEFORE FILLING THE COOLANT RESERVOIRLYING DOWN HORIZONTAL INSTALLATIONSee Parts Lists for Itemʼs below AVOID SPILLING COOLANT INTO THE LOUVERS ON THE TOP OF THE COOLERINSTALLATION Remove the connector nut from the INLET hose by making a straight cut 6-12mm1/4-1/2 away from the end of the nipple located inside of the hose. Take the nipple and the connector nut ordered above and insert the nipple into the connector nut so that the threaded end of the connector nut points away from the barbed end of the nipple. Twist the barbed end of the nipple into the hose until the shoulder of the nip- ple is flush with the end of the hose. Secure the hose onto the nipple with the hose clamp to insure that the connection is watertight. No water can leak from the connection if it is properly attached. Repeat the proce- dure for the OUTLET hose. When complete, follow the connection procedure detailed above for connecting the hoses to the COOL ARC 40 fittingsK529-10 POWER INPUT CABLE WITH WATER INSTALLATIONthe COOL ARC 40. When a solenoid valve clos CONNECTION TO WIRE FEEDERSTURNING THE SYSTEM ON OPERATIONRECOMMENDED PROCESSES AND EQUIPMENT COOL ARCCOOLING EFFICIENCY Coolant Circulation DiagramOPERATION For exampleField Installed CGA style hose fittings ACCESSORIESK529-10 Power Input Cable with Water and Gas Hoses K559-2 Cooler Horizontal Mounting BracketMAINTENANCE SAFETY PRECAUTIONSAlways switch off the COOL ARC 40 machine power MAINTENANCEProcedure and Preparation Always disconnect the COOL ARC 40 machine from service input powerRemoving Coolant MAINTENANCEa. Drain coolant from the reservoir using clean siphon- ing equipment Add coolantStep 1. LOCATE PROBLEM SYMPTOM TROUBLESHOOTINGHOW TO USE TROUBLESHOOTING GUIDE Step 2. POSSIBLE CAUSEField Service Facility TROUBLESHOOTINGMISADJUSTMENTSS POSSIBLE AREAS OFMTR1 DIAGRAMSMTR2 INPUTA L11540 DIMENSION PRINTFILL CAP COOL ARCCOOL ARC WARNUNG AVISO DEPRECAUCION ATENÇÃOWARNUNG AVISO DEPRECAUCION ATENÇÃOSales and Service through Subsidiaries and Distributors Worldwide Worlds Leader in Welding and Cutting Products