14
|
|
|
|
|
|
|
|
| Joints | |
Chimney |
|
|
|
|
| 4' | Required | At | 6' | |
|
|
|
|
| Past | |||||
Section |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Screws | Joint |
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| Offset | Every |
|
|
|
|
| Required 6' | In | of |
| No. 8 x 1/2" SMS | ||||
| 6' |
|
|
| ||||||
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| ||
|
| First |
|
|
|
|
|
|
| |
| Screws | For |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
No | Joints |
|
|
|
|
|
|
|
|
|
Figure 39
Underside Of Chimney
Figure 40
Chimney Section (S)
B |
A
*Part of Offset/Return Package Model
Figure 41
INSTALLING OFFSETS
First, review the Offset Elevation Chart and Figure 41 for reference.
Step1.Determinetheoffsetdistancewherechim- ney is to pass through the first
Measure height to the ceiling from the top of
Step 2. Proceed by using the Straight Up Instal- lation Instructions for cutting and framing ceil- ing and roof openings.
Note: See Framing and Dimension Chart for the sizes of the ceiling and roof openings. The size of the roof opening varies with the degree of pitch of the roof.
Offset Elbow Assembly
Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section of flue. Check connec- tion by pulling up slightly to ensure a tight fit. Next, the outer sections snap lock OVER the preceding outer section of chimney. Again, check outer section by pulling up slightly to ensure proper connection is made.
Return Elbow Assembly
Return elbows install the same way as round terminations and stabilizers:
Step 1. Hold return elbow over top of last chimney section.
Step 2. Center inner slip section into inner flue
Step 3. Center
Step 4. Pull up slightly on return elbow to ensure locking joint has firmly engaged.
Step 5. Secure support straps to framing members by nailing under tension in sheer (Figure 42 ).
Return
Elbow
Figure 42
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Note: The return elbow assembly performs the same function as a stabilizer. Consider this when determining the need for a stabilizer.
Note: Do not apply excessive pressure to any subsequent chimney section following return elbow assembly when installing. Ensure that each subsequent chimney section is securely attached by testing as noted above.
OPTIONAL EQUIPMENT
CONSIDERATIONS
Blower Kits (Circulating Models Only)
Blower Kits model
Note: These fireplace models require a wall switch for fan operation. Refer to the installa- tion instructions included with the Blower Kits for installation details.
THE FIREPLACE MUST BE WIRED TO THE HOUSE ELECTRICAL SYSTEM AT THE TIME OF INSTALLATION IN ORDER FOR THE OP- TIONAL FANS TO OPERATE, (SEE FIGURES 43 AND 44 ).
Note: The utilization of fans will increase the air flow around the firebox. However, only a minimal increase in heat output should be anticipated.
POWER TO THE FIREPLACE The Optional Blower Kit Operates on 115 volt 60 Hz 150 watts AC
HOUSE
WIRING
| GROUND |
| WIRE |
| COVER PLATE |
House Wiring Must Be Secured | Replace Cover Plate |
With The Appropriate Electrical | After Electrical |
Connector To The Fireplace | |
Convenience Outlet Wiring |
|
Figure 43
THIS FIREPLACE IS NOT INTENDED TO BE USED AS A SUBSTITUTE FOR A FURNACE TO HEAT AN ENTIRE HOME. USE FOR SUPPLE- MENTARY HEATING ONLY.