Lok8u K8SLI Layout of K8SLI, Configuration

K8SLI

Configuration

Layout of K8SLI

Contents

Copyright Disclaimer FCC Compliance Statement You have to know Package Contents Symbols Dimensions (ATX form-factor): Operating System: Contents CHAPTER 1. GETTING STARTED INSTALLATION NOTE the 2-pinto 3-pinadapter Page Chapter 1. Getting Started CPU: Chipset: DRAM Memory: PCI-ExpressBUS Slots: PCI BUS Slots: LAN PHY Chip (Vitesse CIS8201): Universal Serial Bus: IDE Facilities: Serial ATA2 facilities: I/O facilities: ABS (Albatron BIOS Security): Green Functionality: Shadow RAM: Flash Memory: Hardware Monitor Function: Layout of K8SLI CPU Processor Installation CPU Socket 939 Configuration Steps: FAN Headers Memory Installation To Enable Dual-ChannelDDR, the following conditions must be met: Please refer the table below to install the memory DIMMs 64-bits Single channel RAM Module Installation: Back Panel Configuration PS/2 Mouse & PS/2 Keyboard Connectors: KB/MS Serial and Parallel Interface Ports USB & GBLAN Connectors: USB/ GBLAN Audio Port Connectors: Sound Front Panel Indicator: SW/LED、SPEAKER HD LED (Hard Drive LED Connector) RST SW (Reset Switch Connector) PWR SW (Power on Switch Connector) SPEAKER (Speaker Header) Connectors Floppy Disk Connector: FDC Hard Disk Connectors: IDE1/ IDE2、SATA1/ 2/ 3 Headers & Jumpers Front USB Headers (Yellow): USB1/ USB2 Front Serial Port Header: COM2 (Optional) Infrared Header: IrDA (Optional) Game Port Header: GAME PORT(Optional) ABS (Albatron BIOS security) Header: BIOSCN1 Clear CMOS Jumper: JP1 Audio Connectors CD-ROM Audio-InHeader: CD-IN Front Panel Audio Header: FRONT AUDIO S/PDIF Header: SPDIF SPDIF & FRONT AUDIO bracket (optional) Slots PCI-Expressslots: PCIE1/ PCIE2/ PCIE3/ PCIE4 PCI Slots: PCI1/ PCI2 Power Supply Attachments ATX Power Connector: ATX_PWR、ATX_12V Chapter 2. BIOS Setup Plug and Play Support EPA Green PC Support APM Support PCI/ PCI-ExpressBus Support Supported CPUs Key Function Main Menu Item Options Description Removable Device Priority Hard Disk Boot Priority CD-ROMBoot Priority First /Second/Third Boot Device Boot Other Device Boot Up Floppy Seek Advanced BIOS Features Advanced Chipset Features Timimng Mode Memclock index value (Mhz) CAS# latency (Tcl) Min RAS# active time (Tras) PnP/PCI Configurations Frequency/Voltage Control HT Ratio HT Frequency PCIE Clock PCIE Spread Spectrum CPU Voltage (Volt) Init Display First IDE Function Setup Primary / Secondary /Master / Slave UDMA IDE Prefetch Mode IDE HDD Block Mode RAID Config RAID Enable Onboard Device Onboard I/O Chip Setup Onboard FDC Controller Onboard Serial Port Onboard Parallel Port Parallel Port Mode EPP Mode Select ACPI Suspend Type Power Management Video Off Method HDD Power Down HDD Down In Suspend Soft-Offby PWRBTN PCI PME Wake Up RTC Wake Up Day of Month Alarm Time (hh: mm: ss) Alarm K8 Cool’n’Quiet Control Shutdown Temperature Load System Default Settings Load System Turbo Settings Load CMOS From BIOS Save CMOS To BIOS Save & Exit Setup Exit Without Saving Chapter 3: Software Setup Page Chapter 4: Troubleshooting Problem 1: Problem 2: Problem 3: Problem 4: Problem 5: Problem 6: Problem 7: Problem 8: Problem 10: Problem 11: Problem 12: Problem 13: Problem 14: Speaker Test Introduction to RAID Disk Striping (RAID 0) Disk Mirroring (RAID 1) Disk Striping + Mirroring (RAID 0+1) RAID SPAN NVIDIA RAID Utility Configuration Associating Screen Drive Names with Physical Drives on the Board Creating New RAID Array RAID 1 mode (Array List) RAID 1 mode (Array Detail) Deleting an Array Rebuilding a RAID Mirrored Array Before you rebuild a RAID Mirrored Array Installing RAID Drivers during Windows Installation Preparation Introduction: Requirements: Installation