Other Accessories | Lowrance electronic X105C DF, X100C specs

In-Dash Installation

You can mount the unit in the dash with an optional FM-5 In-Dash Adapter Kit. The kit includes mounting hardware, a template for cut- ting the hole and an instruction sheet, part 988-0147-43.

146.5

[5.76]

Top

R 7.9 [0.31]

In-Dash

113.5

Template[4.46]

Millimeters

[Inches]

ALWAYS VERIFY DIMENSIONS

In-dash mounting template for the sonar unit, showing

dimensions. NOTE: The figure above is not printed to scale. A scaled template (FM-5 In-Dash Adapter Kit instructions) is available for free download from our web site, www.lowrance.com.

Portable Installation

Like many Lowrance products, this sonar unit is capable of portable operation by using an optional portable power pack. The power pack and an optional portable transducer expand the uses for your sonar unit. The power pack makes it easy to use the unit on your boat or take it to the dock, on a float tube, on an ice fishing trip or use it as a second sonar in a friend's boat. Look inside the back cover of this manual for accessory ordering information.

Other Accessories

Two switch boxes are available for this unit. The SB-9BL transducer switch box switches two transducers to one sonar unit. The SB-10BL transducer switch box switches two sonar units to one transducer.

29

Image 33

Lowrance electronic X105C DF, X100C manual Other Accessories, In-Dash Installation, Portable Installation

Contents

X100C X105C DF Lowrance Electronics Inc 12000 E. Skelly Dr Tulsa, OK USA Table of Contents Page Read Me First Page How Sonar Works Menu Commands How to use this manual typographical conventionsArrow Keys Keyboard Preparations Transducer Installation Dual-frequency transom installations Single-frequency transom installationsSingle-frequency trolling motor installations Shoot-through hull installations How low should you go? Deadrise less than Strakes PadGood location Poor location Location Poor angle Transom Transducer centerline Hull bottom Shoot-thru-hull vs. Transom Mounting Dot Assembling the bracket TransducerTransducer bracket Ratchet Aligning the transducer on the transom Ratchets Drilling mounting holes Assembling the transducer Transom Attaching transducer to transom Bottom Hull Flat-bottom hull Deep-vee hull TMB-S bracket Internal tooth washer Bolt Nut Flat washer Trolling Motor Bracket Installation single-frequency only Hulls With Floatation Materials Partial fish archesTransducer aimed Transducer location High speed Trolling speed Testing Determines Best Location True bottom Second bottom Manual range setting Spread epoxy here Sand this surface Shoot-thru-hull Installation Optional Speed Sensor Installation Optional Temperature Sensor Transom Bottom of hull Good location Powering a Nmea 2000 Buss Nmea 2000 Power cable Power Connections Powering Your Unit Power Supply cable red and black wires Power connections for the units in this series Nmea 2000 Cable Connections Connecting to a Nmea 2000 NetworkNmea 0183 Cable Connections To Nmea To sonar Network port Units Network Socket Mounting the Unit Bracket, In-Dash or Portable Front Bracket Installation 173.9 77.1 27.6 137.9 Millimeter 56.9 Inch Other Accessories In-Dash InstallationPortable Installation Face Cover Keyboard Basic Sonar Operation Main Menu Power/lights on and off Main Menu Pages Page Sonar Page, showing full sonar chart mode Basic Sonar Quick Reference Sonar Operations To adjust sensitivity To Restore Factory Settings Fish Symbols vs. Full Sonar Chart Other Free Training Aids Page To change the ASP level ASP Advanced Signal Processing Depth Alarms Alarms Zone Alarm Fish Alarm Calibrate Speed Chart Speed ColorLine Thin or no ColorLine Wider ColorLine Depth Cursor Cursor line Depth box Depth Range Automatic Depth Range Manual To switch to Manual Depth RangeDepth Range Upper and Lower Limits To turn Auto Depth Range on again Fish arches Area zoomed To change the upper and lower limits Fish I.D. Fish Symbols & Depths FasTrackTo turn off upper and lower limits To turn the Fish I.D. feature on FishTrackTo turn on FishTrack Frequency Change Transducer Frequency X105C DF only Symbols with FishTrack depths To change the frequency setting to 200 kHz To change the frequency setting to 50 kHzHyperScroll Noise Rejection To turn off displayed data To change displayed data font size Ping Speed & HyperScroll To change Ping Speed Reset Options Reset Water DistanceTo turn off HyperScroll Set Keel Offset Automatic Sensitivity Sensitivity & Auto Sensitivity To adjust sensitivity in auto mode To adjust sensitivity in manual modeTo turn Auto Sensitivity back on Sonar Page & Sonar Chart Display Options Sonar Color ModeTo change the chart mode color scheme Full Sonar Chart Digital Data/Chart Split Zoom Sonar Chart Customizing the Digital Data/Chart Screen FlashGraf Flasher Sonar Simulator Stop Chart To adjust the Surface Clarity levelSurface Clarity Zoom & Zoom Bar Upper and Lower Limits Zoom Pan Page Unit freezes, locks up, or operates erratically Unit wont turn on Noise No fish arches when the Fish I.D. feature is offPage Page Supplemental Material Index Page Page Page Lowrance Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service… Accessory Ordering Information for all countries Visit our web site