Transducer Orientation and Fish Arches | Lowrance electronic X67C

3.Route the transducer cable alongside the trolling motor shaft. Use plastic ties (not included) to attach the transducer cable to the troll- ing motor shaft. Make sure there is enough slack in the cable for the motor to turn freely. Route the cable to the sonar unit and the trans- ducer is ready for use.

Transducer mounted on trolling motor, side view.

TRANSDUCER ORIENTATION AND FISH ARCHES

If you do not get good fish arches on your display, it could be because the transducer is not parallel with the ground when the boat is at rest in the water or at slow trolling speeds.

Partial fish arches

Transducer aimed	Transducer aimed
too far back	too far forward

Full fish arch

Proper transducer angle

Transducer angles and their effects on fish arches.

12

Image 16

Lowrance electronic X67C manual Transducer Orientation and Fish Arches, Partial fish arches Transducer aimed Too far back

Contents

X67C Page Table of Contents Depth Range Upper and Lower Limits Capabilities and Specifications X67C Introduction How Sonar Works How to use this manual typographical conventions Press ↓ to Fish ID Symbolsentexitexit Installation and Accessories Installation Preparations Trolling motor installations Transom installationShoot-through hull installations Good location Poor location Location Poor angle Transom Transducer centerline Hull bottom Transom Transducer Assembly and Mounting Dot Ratchets Metal Nut washer RubberWashers Bolt Transom Bottom Hull Flat-bottom hull Deep-vee hull Trolling Motor Bracket Installation Internal tooth washer TMB-S bracket Bolt Nut Flat washer Partial fish arches Transducer aimed Too far back Transducer Orientation and Fish ArchesFull fish arch Proper transducer angle SHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Speed/Temperature Sensors Spread epoxy here Sand this surface Sonar unit Rear view HST-WSU Good location Power Connections Transom Bottom of hullPage 107.5 82.7 76.9 Millimeter Inch 70.3 Using the Quick Release Mounting Bracket Bracket front Depress ratchets to release PPP-12 Portable Power Pack with an X67C stowed for transport Page Tie nylon cord here Suction Cup Bolt Nut Washer TransducerCup Hull Transducer Basic Sonar Operation Menus MemoryExit Main Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Sonar Operations Bait School Thermocline With fish Fish ArchesPage To Restore Factory Settings Important Tip Other Free Training Aids Advanced Sonar Options & Other Features ASP Advanced Signal Processing Alarms To adjust and turn on the shallow alarm To turn the fish alarm on To adjust and turn on the deep alarmBacklight Level Chart Speed Calibrate Speed ColorLine Contrast Thin or no Colorline Wider Colorline Depth Cursor Cursor line Depth box To switch to Manual Depth Range Depth Range AutomaticDepth Range Manual To turn Auto Depth Range on again Depth Range Upper and Lower Limits FasTrack Area zoomed Fish I.D. Fish Symbols & Depths Symbols with FishTrack depths FishTrackHyperScroll Noise Rejection Overlay Data To turn off displayed data Ping Speed & HyperScroll To change displayed data font size To adjust Sensitivity From the Sonar Page, press Menuent Pop-up Help To turn off HyperScroll Reset Options Reset Water DistanceScreen Contrast and Backlight Level Sensitivity & Auto Sensitivity Automatic Sensitivity Set Keel Offset Set Language Press MENUMENU↓ to SET Keel Offsetent Software Version Information Sonar Color ModePress MENUMENU↓ to Software Infoent Sonar Page & Sonar Chart Display Options Digital Data/Chart Stop Chart Sonar Simulator Surface Clarity Press ↓ or ↑ to select clarity levelEXITEXITEXIT Transparency Units of Measure Upper and Lower Limits VolumeZoom & Zoom Bar Zoom Pan To turn on the Zoom BarPage Troubleshooting Page Noise Page Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site