Mackie 1402-VLZPRO POWER CONNECTION, POWER SWITCH, PHANTOM SWITCH, FUSE, POWER, power is on, so is the LED, LED. If the power is on, so is the LED, WARNING: Disconnect

POWER CONNECTION

Just in case you lose the cord provided with the 1402-VLZ PRO, its power jack accepts a standard 3-prong IEC cord like those found on most professional recorders, musical instru- ments, and computers.

At the other end of our cord is — get this

—a plug! Not a black cube or, as we’re fond of calling them, a “wall wart.” We did this for some very good reasons:

The 1402-VLZ PRO has sophisticated power requirements that a wall wart cannot provide. Wall warts are inconvenient, fragile, radiate huge hum fields, hog extra jacks on your power strip and get in the way. If you lose a wall wart, you’re in trouble, but if you lose the 1402-VLZ PRO’s power cord, you can get a new one at any electronics, music, or computer store. You can even buy them at Radio Shack® (part # 287-1257). Can you tell that we hate wall warts?

Plug the 1402-VLZ PRO into any standard grounded AC outlet or into a power strip of proper voltage.

WARNING: Disconnect-ing the plug’s ground pin can be dangerous. Please don’t do it.

POWER SWITCH

If this one isn’t self-explanatory, we give up. You can leave this switch on all the time; the 1402-VLZ PRO is conservatively designed, so heat buildup isn’t a problem even in 24-hour-a- day operation. There’s nothing that will burn out or get used up. Or, just plug everything into a good quality power strip for one-button turn-on.

You may notice that the 1402-VLZ PRO feels quite warm in the upper- right corner. This is

perfectly normal. (Perfectly normal. Is that redundant?) In the output section there is a POWER

LED. If the power is on, so is the LED.

PHANTOM SWITCH

The Phantom Power Switch controls the phantom power supply for condenser microphones plugged into channels 1-6 mic inputs as discussed at the start of this section .

When turned on (or off), the phantom power circuitry takes a few moments for voltage to ramp up (or down). This is also perfectly normal. In the output section, next to the POWER LED, is the PHANTOM LED. If the phantom

power is on, so is the LED.

FUSE

The 1402-VLZ PRO is fused for your (and its own) protection. If you suspect a blown fuse, disconnect the cord, pull the fuse drawer out (located just below the cord receptacle) and replace the fuse with a 500mA (0.5 amps) SLO BLO, 5x20mm, available at electronics stores or your dealer (or a 250mA SLO BLO 5x20mm if your 1402-VLZ PRO is a 220V–240V unit).

If two fuses blow in a row, something is very wrong. Please call our toll-free number (or the distributor in your country) and find out what to do.

120 VAC 50/60 Hz 25W 500mA/250V SLO-BLO

CAUTION:

TO REDUCE THE RISK OF FIRE REPLACE WITH SAME TYPE FUSE AND RATING

POWER

PHANTOM

MONO PLUG

PLUG

CAUTION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

SERIAL NUMBER

MANUFACTURING DATE

STEREO

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.

1402-VLZPRO

RISK OF ELECTRIC SHOCK

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

INSERT ALL THE WAY IN TO

TIP OUT TO EFFECTS DEVICE

DO NOT OPEN

AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

14-CHANNEL MIC/LINE MIXER

THE "SECOND CLICK"

RING RETURN FROM EFFECTS

WITH PREMIUM XDRTM MIC PREAMPLIFIERS

DIRECT OUT WITH SIGNAL

FOR USE AS AN EFFECTS LOOP

REPLACE WITH THE SAME TYPE FUSE AND RATING.

UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.

INTERRUPTION TO MASTER

(TIP= SEND, RING = RETURN)

DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE

DEBRANCHER AVANT DE REMPLACER LE FUSIBLE

XDRTM EXTENDED DYNAMIC RANGE MIC PREAMPLIFIERS ARE PROPRIETARY TO MACKIE DESIGNS, INC.

MAIN

CONTROL

ALT

CHANNEL INSERT

RIGHT

LEFT

ROOM

OUTPUT

BALANCED

BAL/UNBAL

BAL /UNBAL

( PRE-FADER / PRE EQ

TIP SEND / RING RETURN)

)

R/4

L/3

MIC

MAIN

OUTPUT

LEVEL

THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "VLZ", "XDR", AND THE "RUNNING MAN" FIGURE • PATENT PENDING