8.In MONO and BRIDGE modes, connect an input cable to CHANNEL 1’s INPUT only, and nothing into CHANNEL 2’s INPUT. (You could plug into CHANNEL 2’s input, it just won’t do anything.)

9.In STEREO and MONO modes, connect speaker cables to the SPEAKER OUTPUTS , either binding posts, 1/4” jacks, or Speakon®, depending on your model:

•The binding post connectors are wired red = hot (+) and black = cold (–).

•The 1/4" jacks are wired tip = hot (+) and ring = cold (–).

•The Speakon connectors are wired

pin 1+ = hot (+) and pin 1– = cold (–).

10.In BRIDGE mode, connect the binding post

cable like this: the hot (+) side goes in the

CHANNEL 1 SPEAKER OUTPUTS red post and the cold (–) side goes in CHAN- NEL 2’s red post. Plug nothing into the black posts, Speakon jacks (on the M•1400), or the 1/4" TS jacks (on the M•1400i).

11.Connect the other ends of the speaker cables to your loudspeakers.

12.Plug the amp’s power cord into an outlet properly configured with the correct voltage for your amplifier, and capable of delivering enough current to reach full power.

13.Make sure your signal source (feeding the M•1400/M•1400i’s inputs) is powered up and delivering signal to the amp.

14.Turn the M•1400/M•1400i’s POWER switch on and verify that the signal present (SIG) LEDs are blinking.

15.Slowly turn both GAIN controls up:

are flashing, turn down either the GAIN controls on the amp or the source signal’s output level controls (i.e., master faders). The point is: The OL LEDs should never light up.

16.For quieter listening, it is preferable to adjust the amp’s GAIN controls rather than the source signal’s output level (unless you have the source’s control all the way up!).

17.Start dancing, but don’t let the ants out of your pants.

Things You Must Remember:

• Read and follow the safety instructions on page 2, and the hearing protection details on page 3, before using the amplifier.

•Never plug amplifier outputs into any- thing except speakers (unless you have an outboard box specifically designed to handle speaker-level signals).

•Before making connections to an amp or reconfiguring an amp’s routing, turn the amp’s level (GAIN) controls down, turn the power off, make the changes, turn the power back on, and then turn the level controls back up.

•If you shut down your equipment, turn off the amplifiers first. When powering up, turn on the amplifiers last.

•Save the shipping boxes! You may need them someday, and you probably don’t want to have to pay for them again.

You should hear the music and see the SIG and meter LEDs flashing. If the topmost LEDs (named OL, for OverLoad)

 

 

 

 

CAUTION

 

 

 

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.

SERIAL NUMBER

MANUFACTURING DATE

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

 

 

 

 

 

RISK OF ELECTRIC SHOCK

 

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

 

 

 

 

 

 

DO NOT OPEN

 

 

 

AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

 

 

 

 

 

 

 

CONCEIVED AND DESIGNED BY MACKIE DESIGNS INC • WOODINVILLE • WA

 

 

 

 

 

98072 • USA • MADE IN CHINA • FABRIQUE AU CHINE • PATENTS PENDING • COPYRIGHT ©1997

 

 

(MONO BRIDGE)

 

THE FOLLOWING ARE TRADEMARKS AND REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "FR SERIES", AND THE "RUNNING MAN" FIGURE

1000 WATTS

OUTPUTS

 

 

 

 

 

 

 

 

MONO

 

 

 

 

 

 

OUTPUTS

 

 

8 OHM LOAD

 

CH

 

 

–

 

 

 

CH

 

 

(STEREO)

SUITABLE

 

+

 

BRIDGE

 

 

SUITABLE

 

 

500 W / 500 W

FOR CLASS

1

 

 

 

 

 

 

 

 

 

 

 

 

2

FOR CLASS

 

 

4 OHM LOAD

2 WIRING

 

 

 

 

 

 

 

 

 

 

 

 

2 WIRING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1CHANNEL / BRIDGE / MONO

LOW CUT

INPUT

 

FILTER

 

 

TYPICAL

BALANCED

 

OR

 

35 Hz

UNBALANCED

 

STAGE

 

 

MONITOR

 

 

100 Hz

 

OFF

170 Hz

 

 

CONSTANT DIRECTIVITY

AMP MODE

STEREO

MONO

BRIDGE

TYPICAL

(CHS SUMMED)

 

 

OUTPUT APPLICATION

 

 

FULL

 

 

 

SUB

 

 

 

 

RANGE

 

WOOFER

 

LIMITER (CH1 & CH2)

 

 

 

 

INPUT

CHANNEL 2

LOW CUT

 

 

FILTER

BALANCED

 

TYPICAL

OR

 

UNBALANCED

 

35 Hz

 

 

STAGE

 

 

MONITOR

 

 

100 Hz

 

OFF

170 Hz

CONSTANT DIRECTIVITY

120 VAC 60 Hz 1000 WATTS

++

– –

 

HORN EQ/AIR EQ

 

4.5 kHz

ON

 

 

2k Hz

6k Hz

OFF

 

AIR EQ

 

 

TYPICAL

 

FREQUENCY

STEREO

125Hz

TYPICAL

ON OFF

63Hz

 

HORN EQ /AIR EQ

 

ON

4.5k Hz

 

 

 

2k Hz

6k Hz

OFF

 

AIR EQ

TYPICAL

 

 

SPEAKER OUTPUTS

THRU

THRU

5