Magnavox MT1931B, MT1340B warranty Hooking UP Your TV ANTENNA/CABLE Connections, Antenna, Cable TV

HOOKING UP YOUR TV (ANTENNA/CABLE CONNECTIONS)

ANTENNA

COMBINATION UHF/VHF

Acombination antenna receives normal broadcast

channels (VHF 2-13 and UHF 14-69). Your connection is easy since there is only one 75Ω (ohm) antenna jack on the back of your TV - and that’s where the antenna goes.

Combination

VHF/UHF

Antenna

(Outdoor or

Indoor)

If your antenna has a	Push the round end of
round connector (75Ω ),	the adaptor (or cable) onto
then you're ready to connect it	the ANT(enna) IN jack on
to the TV.	the back of the TV. If the
If your antenna has flat	round end of the adaptor or
twin-lead wire (300Ω ), you	cable is threaded, screw it
first need to attach the antenna	down tight.
wires to the screws on a 300
to 75Ω adaptor.
	300 to 75Ω
	Adaptor
Twin-lead
Wire

SMART

HELP

To set the

TV to select only the channel num- bers in your area, see Auto Install on page 3.

Round Cable 75Ω

Back of TV

SEPARATE UHF/VHF

You may have two separate antennas. One antenna is for VHF channels (2-13) and the other antenna is for UHF

channels (14-69).

For homes with separate UHF/VHF antennas, you will need an optional combiner before you can connect the antennas to the TV.

Attach the separate
	Push the round end of the
UHF and VHF antennas to	combiner onto the ANT(enna)
the correct screws on the	IN jack on the back of the TV.
combiner.

UHF/VHF

Combiner

SMART

HELP

To order any optional accessory, contact your dealer. Or, call 1-800-851-8885 and refer to the fol- lowing part num- bers to order.

• UHF/VHF

Combiner:

4835 466 97016

Twin-lead

Round

• 75-300Ω

Outdoor UHF Antenna

(Twin-lead 300Ω )

Outdoor VHF

Antenna

(Twin-lead 300Ω )

Outdoor VHF

Antenna

(Round cable 75Ω )

Wire

End

Adaptor:

M61009

• 300-75Ω

Adaptor:

4835 218 27003

75-300ΩAdaptor

Back of TV

CABLE TV

CABLE/CABLE BOX

Your Cable TV signal may be a single (75Ω ) cable or a Cable Box installation. In either case, the connection to the TV

is very easy.

Cable TV Company

If you do not have a Cable Box, then you're ready to connect your Cable TV sig- nal to the TV. Go to step 2.

If you have a Cable Box: Connect the Cable TV signal to the IN jack on the Cable Box.

Cable TV Signal (75Ω )

If you do not have a Cable Box, connect the Cable TV signal directly to the ANT(enna) IN jack on the TV.

If you have a Cable Box: Use a coaxial cable to connect the OUT jack of the Cable Box to the ANT(enna) IN jack on the TV.

NOTE: The coaxial cable might be supplied by the Cable TV company.

SMART

HELP

To select

only the channels on your Cable system, see Auto Install (page 3).

If you use a Cable Box, set the TV to the same channel as the CH 3/4 switch on the back of the Cable Box and select channels at the Cable Box.

Cable Box

Coaxial cable

Note to the Cable TV System Installer: This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

Back of TV

- 2 -