Magnavox Rear-projection HDTV Monitor setup guide Hooking Up The Tv, Best Viewing, Cable Tv

NOTE: Refer to the sections on TUNER MODE and AUTO PROGRAM on page 4 of this guide. Set TUNER MODE to the CABLE option. Run AUTO PROGRAM to store all available cable channels in the TV’s memory..

Be sure to set the Output Channel switch on the back of the cable box to CH 3 or 4, then tune the cable box on the TV to the corresponding channel. Once tuned, change channels at the cable box, not the TV.

This is for example purposes only. The back of your cable box may be labeled somewhat differently.

This connection WILL NOT supply stereo sound to the TV.

Rear-projection

HDTV Monitor

S M A R T. V E R Y S M A R T.

Quick-Use and Setup Guide

CONTENTS
Important Notice/Warning	1
Hooking up the TV	1–2
Operating the Television and Remote Control	2–3
Using the Installation Features	4–6
Adjusting the Manual Converge Controls	7

As an Energy Star® Partner, Magnavox has deter- mined this product meets the Energy Star® guidelines for energy efficiency. Energy Star® is a U.S. registered mark. Using products with the Energy Star® label can save energy. Saving energy reduces air pollution and lowers utility bills.

IMPORTANT

This owner's manual is used with several different television models. Not all features (and drawings) discussed in this manual will neces- sarily match those found with your television set. This is normal and does not require that you contact your dealer or request service.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR EXCESSIVE MOISTURE.

HOOKING UP THE TV

BEST VIEWING

The major benefit of this projection television is its large view-

ing screen. To see this large screen at its best, test various locations in the room to find the optimal spot for viewing.

NOTE: Be sure to allow a free flow of air to and from the perfo- rated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot—for example, in direct sunlight or near a heating appliance.

Magnetic fields, such as those of external speak- ers, may cause the picture to distort if the speak- ers are placed too close to the television. Move the magnetic field source away from the TV until there is no picture distortion.

CABLE TV

This connection WILL supply Stereo sound to the TV.

1 Connect the cable TV signal to the ANTENNA IN 75Ω jack on the back of the TV.

NOTE: Refer to the sections on TUNER MODE and AUTO PROGRAM on page 4 of this guide. Set TUNER MODE to the CABLE option. Run AUTO PROGRAM to store all available cable channels in the TV’s memory.

Cable TV

Signal

	1			Back of TV
				HD INPUT-AV 5
				DVI
				HD INPUT-AV 4
				G/Y
ANTENNA IN 75Ω				R/Pr
	INPUT-AV 1	OUTPUT	INPUT-AV 2
		Y		B/Pb
	VIDEO		VIDEO
	S-VIDEO		S-VIDEO
	L	Pb		V
					L
	L		L	L
				SYNC
	AUDIO	Pr	AUDIO	AUDIO	AUDIO
				H
	R		R	R	R

CABLE BOX WITH RF IN/OUT

Cable TV

Signal

Connect the cable TV signal to the CABLE IN jack on
1 the back of the cable box.	1
Connect a coaxial cable (not supplied) to the TO TV
jack on the back of the cable box and to the ANTENNA
2 IN 75Ω jack on the back of the TV.
		OUTPUT
			CH
	CABLE	3	4
		TO TV

3 IN

	2			Back of TV
				HD INPUT-AV 5
				DVI
				HD INPUT-AV 4
				G/Y
ANTENNA IN 75				R/Pr
	INPUT-AV 1	OUTPUT	INPUT-AV 2
		Y		B/Pb
	VIDEO		VIDEO
	S-VIDEO		S-VIDEO
		Pb	L
	L			V
					L
	L		L	L
				SYNC
	AUDIO	Pr	AUDIO	AUDIO	AUDIO
				H
	R		R	R	R

3	Back of Cable Box
	(example only)

CABLE BOX WITH A/V OUTPUTS

This is for example purposes only. The back of your cable box may be labeled somewhat differently.

This connection MIGHT supply stereo sound to the TV. Check with your cable TV company.

1 Connect the cable TV signal to the CABLE IN jack on the back of the cable box.

2 Connect A/V cables to the VIDEO and AUDIO outputs on the back of the cable box and to the corresponding INPUT-AV 2 jacks on the back of the TV.

3 Be sure to set the Output Channel switch on the back of the cable box to CH 3 or 4, then tune the cable box on the TV to the corresponding channel. Once tuned, change channels at the cable box, not the TV.

NOTE: Refer to the sections on TUNER MODE and AUTO PROGRAM on page 4 of this guide. Set TUNER MODE to the CABLE option. Run AUTO PROGRAM to store all available cable channels in the TV’s memory.

Cable TV	3
Signal
	Back of Cable Box
	(example only)

OUTPUT

CH

	3	4
CABLE	TO	VIDEO	L AUDIO R
IN	TV	OUT	OUT

1

			DVI	2 Back of TV
				HD INPUT-AV 4
				G/Y
ANTENNA IN 75Ω	INPUT-AV 1		INPUT 2	R/Pr
				B/Pb
	VIDEO		VIDEO
	S-VIDEO
	L			V
					L
	L		L	L
				SYNC
	AUDIO	Pr	AUDIO	AUDIO	AUDIO
				H
	R		R	R	R

3135 035 22994- English