Disconnect the antenna or cable from your TV | Magnavox VR602BMG

6 Hookups Without a Cable Box/Direct Broadcast System

The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. (The VR602BMG is illustrated here. The VR402BMG has single AUDIO IN/OUT jacks.)

1

Disconnect the antenna or cable from your TV.

Antenna

Indoor/Outdoor

(300 ohm)

75 ANT / CABLE

75V

ANT /

CABLE

OR

ANTENNA IN

Jack

(on back of TV)

Cable

(75 ohm)

2

Connect the antenna or cable to the ANT(enna) IN Jack of your VCR.

Antenna

Indoor/Outdoor

(300 ohm)

OR

Cable

(75 ohm)

Back of VCR

			AUDIO		ANT
			L		IN
			OUT	IN
			R
		ANT	VIDEO		OUT
					OUT
			OUT	IN	CH3 CH4
AUDIO
AUDIO		IN
	L	IN
	L
OUT	IN
	R
VIDEO		OUT
VIDEO
OUT	IN CH3	CH4

Image 6

Magnavox VR602BMG Hookups Without a Cable Box/Direct Broadcast System, Disconnect the antenna or cable from your TV

Contents

VCR Warranty Verification For Customer Use Introduction FeaturesSafety Precautions Declaration of Conformity Table of Contents VCR maintenance Before Using Your VCRPutting Batteries in the Remote Control Replace the battery compartment lid Hookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCR Hookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Cable Signal Cable Box/DBS Recording One Channel/Watching AnotherTV’s Antenna Hookups with a Stereo TV VR602BMG Turning on Your VCR 2Turn on the TVPress the Menu button. The display shown below will appear Automatic Channel Setup Press the Menu buttonVR602BMG only Automatic Channel Setup cont’d Adding/Deleting Channels Reviewing Memorized Channels Press the STATUS/EXIT button once or twice to exit Setting the Clock Enter a 0 before a single-digit number Daylight-Savings Time Language Selection Press the STATUS/EXIT button Remote Control Buttons Remote Control Buttons cont’d Clear ButtonChannel o/p Buttons If you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFF VCR Display Panel Front Panel Rear Panel VHS Quasi Play Back Sqpb Other playback options and features are on pagesPlaying Read and follow the steps below to play a tape Insert a tape with its record tab intact in the VCR VCR will record in a preset vol- umeRecording VCR Light does not appear, press the VCR/TV button once Recording One Channel/Watching Another One-Touch Recording Timer Recording Do each step within 60 seconds of the previous stepDaily Timer Recording cont’d Instructions continue on Tape Speeds Checking or Cancelling Timer Recordings Rerecording Tape Duplication RF coaxial cable Repeat Play Press the PLAY/o button or the STOP/p button to selectPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Time Search Press the Time Search button Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still Picture Automatic Operation Features This indication is not available during tape playback Understanding On-Screen DisplaysSpecifically… Monitor Multi-Channel Television Sound System VR602BMG only cont’d Hi-Fi Stereo Sound System VR602BMG only Please see additional notes on Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 or Specifications Renewed Index Supplied Accessories