Press the Time Search button | Magnavox VR402BMG, VR602BMG manual

Follow the steps below to program the VCR to search forward or backward on a tape a specific length of time. There must be a tape in the VCR.

1

Press the TIME SEARCH button.

TIME SEARCH

0:00

ENTER SEARCH TIME

2

Within 10 seconds, use the Number buttons to enter the desired length of time you want to skip forward or back- ward. For example, for 1 hour, 25 minutes, press Number but- tons 1, 2, 5. Or, for five minutes, press Number buttons 0, 0, 5.

3

Within 10 seconds, press the F.FWD/B button or the REWIND/{ button. The VCR will skip over the specified length of time, then begin playback.

Time Search 35

	POWER		VCR/TV	EJECT
2	1	2	3
	4	5	6
	7	8	9	CHANNEL
1		0
1	SPEED	TIME SEARCH		MEMORY
3	MENU	STATUS/EXIT	CLEAR	SLOW
	REWIND	/PLAY		F.FWD
	REC/OTR	/STOP		PAUSE/STILL

Helpful Hints

•If you want to search for more than 59 minutes, you must enter the length of time in hours and minutes. For example, to search forward 70 minutes, press 1,1,0 at step 2.

•You can not do a Time Search while recording.

•To remove the Time Search display, press the TIME SEARCH button again.

•To cancel a Time Search that is in progress, press the STOP/p button.

Image 35

Magnavox VR402BMG, VR602BMG owner manual Press the Time Search button

Contents

VCR For Customer Use Warranty Verification Declaration of Conformity FeaturesSafety Precautions Introduction Table of Contents Replace the battery compartment lid Before Using Your VCRPutting Batteries in the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Recording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Cable Signal Cable Box/DBSRecording One Channel/Watching Another VR602BMG Hookups with a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV VR602BMG only Automatic Channel SetupPress the Menu button Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Enter a 0 before a single-digit number Setting the Clock Daylight-Savings Time Press the STATUS/EXIT button Language Selection Remote Control Buttons Channel o/p Buttons Remote Control Buttons cont’dClear Button If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only on VCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Other playback options and features are on pagesPlaying VHS Quasi Play Back Sqpb VCR Light does not appear, press the VCR/TV button once VCR will record in a preset vol- umeRecording Insert a tape with its record tab intact in the VCR Recording One Channel/Watching Another One-Touch Recording Daily Timer RecordingDo each step within 60 seconds of the previous step Instructions continue on Timer Recording cont’d Tape Speeds Checking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Real-Time Counter Memory Press the Time Search button Time Search Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Automatic Operation Features Monitor Understanding On-Screen DisplaysSpecifically… This indication is not available during tape playback Multi-Channel Television Sound System VR602BMG only cont’d Please see additional notes on Hi-Fi Stereo Sound System VR602BMG only Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Renewed Index Supplied Accessories