Plug in the TV and the VCR | Magnavox VR402BMG, VR602BMG specification

Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

	AUDIO		ANT
	L		ANT
	L		IN
	OUT	IN
	R
ANT	VIDEO		OUT
	OUT	IN	CH3 CH4

AUDIO		IN
	L	IN
	L
OUT	IN
	R
VIDEO		OUT
VIDEO
OUT	IN CH3 CH4	RF coaxial cable
		RF coaxial cable

75 ANT / CABLE

ANTENNA IN Jack

(on back of TV)

example only

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

			AUDIO		ANT
			L		IN
			OUT	IN
			R
		ANT	VIDEO		OUT
					OUT
			OUT	IN	CH3 CH4
AUDIO
AUDIO		IN
	L	IN
	L
OUT	IN
	R
VIDEO		OUT
VIDEO
OUT	IN CH3	CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Magnavox VR402BMG, VR602BMG Hookups Without a Cable Box/Direct Broadcast System cont’d, Plug in the TV and the VCR

Contents

VCR For Customer Use Warranty Verification Declaration of Conformity FeaturesSafety Precautions Introduction Table of Contents Replace the battery compartment lid Before Using Your VCRPutting Batteries in the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Connections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Cable Signal Cable Box/DBSTV’s Antenna VR602BMG Hookups with a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Press the Menu button Automatic Channel SetupVR602BMG only Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Enter a 0 before a single-digit number Setting the Clock Daylight-Savings Time Press the STATUS/EXIT button Language Selection Remote Control Buttons Clear Button Remote Control Buttons cont’dChannel o/p Buttons If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only on VCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Other playback options and features are on pagesPlaying VHS Quasi Play Back Sqpb VCR Light does not appear, press the VCR/TV button once VCR will record in a preset vol- umeRecording Insert a tape with its record tab intact in the VCR Recording One Channel/Watching Another One-Touch Recording Do each step within 60 seconds of the previous step Timer RecordingDaily Instructions continue on Timer Recording cont’d Tape Speeds Checking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Press the Time Search button Time Search Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Automatic Operation Features Monitor Understanding On-Screen DisplaysSpecifically… This indication is not available during tape playback Multi-Channel Television Sound System VR602BMG only cont’d Please see additional notes on Hi-Fi Stereo Sound System VR602BMG only Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Renewed Index Supplied Accessories