Marantz AV9000 manual Remote Control Unit RC-18SR, Amp

@096 kHz decode indicator

This indicator is for 96 kHz PCM digital input signal. If the selected digital input signal is 96 kHz PCM audio, this indicator will illuminate.

@1DTS CINEMA and MUSIC indicator

These indicators display the currently selected DTS mode. If you select DTS cinema or DTS music by SURROUND MODE SELECTOR buttons u, these indicators will display.

@2ENCODED CHANNEL STATUS indicator

These indicators show which channels are encoded with a digital input signal.

If the selected digital input signal is Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “LS”, “RS” and “LFE” will light up.

If the digital input signal is 2 channel PCM-audio, “L” and “R” will be displayed.

Note:

These indicators are depend on the digital input, without reference to the surround mode.

@3PEAK indicator

This indicator is a monitor for analog audio input signal. If the selected analog audio input signal is greater than the capable level of internal processing, this indicator will show. If this indicator is lit up, you should press the ATT button on the remote control.

REMOTE CONTROL UNIT RC-18SR

This chapter describes the functions which need to control the AV9000. See page 27 and following pages to refer other function of the RC-18SR.

vPOWER ON and OFF

These two buttons are use for turning on or off AV9000.

mDIRECT button

The DIRECT command buttons (4 on each side of the LCD display, 8 total) work with the PAGE buttons (4 pages for each source component) to provide up to 32 dedicated specialized functions for each of the 11 function input selectors. Each DIRECT function may also be provided with an alphanumeric function indicator visible in the LCD display. Press the AMP or TUNER button . to control the receiver.

Press one of these buttons to select a surround mode for the current listening session.

AMP

MODE1	1 AUTO		Auto select surround modes
	2	DOLB	Dolby Digital or Pro Logic decoding
	3	THX	THX cinema decoding
	4	DTS	DTS-cinema or DTS-music
	5	HALL	Hall surround sound
	6	MTRX	Matrix surround sound
	7	MOV	Movie surround sound
	8	2-CH	Stereo sound (no surround)
MODE2	1 A/D		analog / digital select switch
			Switches between the analog input and the
			digital input.
	2	DIR	source direct switch
			When this switch is pressed, the signals are
			transmitted by bypassing the tone control
			circuitry so that they can be reproduced with
			higher quality.
	3	ATT	attenuate for analog input
	4	OSD	on screen display
			Once the button is pressed, the on-screen
			display is turned on and each a control button
			related to the AV9000 is pressed thereafter, the
			information will be displayed on the TV screen.
			When the button is pressed again to turn the
			on-screen display off, it disappears from the TV
			screen . (Refer to “ON - SCREEN MENU
			SYSTEM” on page 10)
	5	MONO	monaural decoding
			When this button is pressed, the monaural
			sound is selected.
	6	3-D	3-D surround decoding
			This button is not used for AV9000.
	7	NITE	NIGHT mode for Dolby Digital
			Pressing this button prevents the Dolby Digital
			signal from playback at a loud voice. This
			function reduces the voice by 1/3 to 1/4 at
			maximum. Thus, it eliminates the occurrence
			of an abruptly loud voice at night. However, the
			function is valid only for the case when the
			Dolby Digital signal (AC-3) is entered into
			digital Input and data to compress the voice
			exists in the signal to be played back.
	8	MLTI	activates multi-room mode
MODE3	1 TRB+		increases treble
	2	TRB-	decreases treble
	3	BAS+	increases bass
	4	BAS-	decreases bass
			The button 1 to 4 are used to control the tone.
	5	R-EQ	activates RE-EQ function
			This button is not used for AV9000.
	6	CH+	channel select button
			Press this button to adjust the volume levels of
			the front, center, surround, subwoofer
			channels. Each press of the button changes
			the channel which can be adjusted.

ENGLISH

7