Manuals / Marantz / Computer Equipment / Computer Monitor

Marantz PD6140D manual Important Information, Attaching the ferrite cores

Models: PD6140D

1 60

Download 60 pages 22.45 Kb

Page 55

Attaching the ferrite cores:

Important Information

Warning

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment ANSI/NFPA 75.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio / TV technician for help.

NOTE:

When you connect a computer to this monitor, use an RGB cable including the ferrite core on both ends of the cable. And regarding DVI and power cable, attach the supplied ferrite cores. If you do not do this, this monitor will not conform to mandatory FCC standards.

Attaching the ferrite cores:

Set the ferrite cores on both ends of the DVI cable (not supplied), and both ends of the power cable (supplied). Close the lid tightly until the clamps click.

Use the band to fasten the ferrite core (supplied) to the DVI cable.

DVI cable (not supplied)
			band	band			Connector





	core (small)			core		(small)

Power cable (supplied)

core (large)

core (large)

Caution

PD6140D is for use with the following optional accessory. Use with other optional accessories is capable of resulting in instability causing possible injury.

Manufacturer’s name: Marantz Japan, Inc.

Stand: AS6140

Please contact Marantz America, Inc. for approved optional accessories.

4

Image 55

Marantz PD6140D manual Important Information, Attaching the ferrite cores

Contents

Model PD6140D User Guide Introduction to the Plasma Monitor The features you’ll enjoy includeContents of the Package IntroductionWarnings and Safety Precaution PrecautionsImportant Information 2. Handle the unit carefully when installing it and do not drop AVERTISSEMENT Recommandations importantesPrécautions Mises en garde et précautions de sécuritéAffichez une image en mouvement aussi souvent que possible Troubleshooting ContentsHow to Attach Options to the Plasma Monitor InstallationSee the inside of the cover page Ventilation Requirements for enclosure mountingHow to Attach Options to the Plasma Monitor Front View Part Names and FunctionC E F G H I J K Rear View/ Terminal BoardD A B Remote Control 5MULTI Battery Installation and Replacement7AUTO ADJUST @0Remote control signal transmitterApprox 7m/23ft Using the wired remote control modeHandling the remote control Operating RangeTo Mini D-Sub 15 pin connector on the plasma monitor Installationdigital signal output Personal computer with aConnections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin Configuration and Signal of the RGB 3 Connector DVI Connector Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallInformation To adjust the sound volume POWERVOLUME AUTO ADJUSTAfter the power is turned off with the off timer OFF TIMERTo set the off timer To cancel the off timer2. Within 3 seconds When viewing videos or digital video discsWIDE Operations Wide Screen Operation manual “PICTURE SIZE” setting Wide Screen Operation with Computer SignalsWhen “PICTURE SIZE” is set to “OFF” Supported resolutionOSMOn Screen Menu Controls Advanced menu modeMenu Operations Note The main menu disappears by pressing the EXIT buttonMenu Tree 3← … → 1 Only when AUTO PICTURE is OFF 2 RGB/PC only1← … → Note If “CAN NOT ADJUST” appears Picture Settings MenuAdjusting the picture Setting the picture mode according to the brightness of the roomReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level Setting the color temperature LOW TONE settings Making the Low Tone adjustments Adjusting the white balance GAMMA settings COLOR TUNE settings Audio Settings MenuAdjusting the colors To continue making other adjustmentsTo select a mode Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture Adj Adjusting the Auto Picture Option1 Settings MenuSetting the on-screen menu When “AUTO PICTURE” is “OFF” OSM ORBITER settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen3. To set the HD SELECT mode to “1035I” Setting high definition images to the suitable screen sizeSetting the Input Skip See page 7 of Model Information for the details of the above settingsRefer to page 16 for items to be reset Option2 Settings MenuResetting to the default values Setting the power management for computer imagesCINEMA MODE POWER/STANDBY indicatorSetting the picture to suit the movie 3. To set the CINEMA MODE to “OFF”Perform Steps 1-3 of ORBITER, then ORBITER settingsORBITER Function settings INVERSE SettingsSCREEN WIPER Setting the timePerform Steps 1-3 of INVERSE, then To select “ON” for the “WORKING TIME”3. To adjust the “GRAY LEVEL” Setting the screen size for S1/S2 video inputSOFT FOCUS settings Setting the gray level for the sides of the screen3. To set PICTURE SIZE mode to “OFF” Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settings5. Once the setting is completed Option3 Settings MenuUsing the timer Perform Steps 1-2 of TIMER, thenSpecial characters in the PROGRAM TIMER screen Setting the power on modeTo reset the program To reset the dataIR REMOTE settings Enabling/disabling remote control wireless transmissionPWR. ON MODE settings CONTROL LOCK settingsIf the RGB/PC1 signal is present at the time the power switched on Loop Out settingID number setting LOOP OUT settingsPerform Steps 1-2 of VIDEO WALL, then Video Wall settingDIVIDER settings VIDEO WALL POSITION settingsSet the ID number for the No. 1 display on ID NUMBER menu AUTO ID settingsDISP. MODE settings IMAGE ADJUST settingsInformation P. ON DELAY settingsPLE LINK settings Perform Steps 1-2 of VIDEO WALL, thenADVANCED OSM settings Advanced OSM Settings MenuSetting the menu mode REPEAT TIMER settingsSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusConnections Type of connector D-Sub 9-pin maleExternal Control ApplicationRemedy TroubleshootingSymptom Checks1 Overheat protector Page Plasma Monitor Model PD6140D InformationIMPORTANT SAFETY INSTRUCTIONS PD6140D Read before operating equipment A lire avant de faire fonctionner l’appareil PRÉCAUTIONS IMPORTANTES DE SÉCURITÉ PD6140DAVERTISSMENT Attaching the ferrite cores Important InformationUse the band to fasten the ferrite core supplied to the DVI cable REMARQUE AvertissementDOC avis de conformation Recommandations importantesPower Supply SpecificationsResolution SignalsSupported resolution Table of Signals SupportedComputer input signals supported by this system DECLARATION OF CONFORMITY EUROPE is a registered trademarkJAPAN U.S.A