SVENSKA PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH
DANSK
CONTROLS, CONNECTORS,
AND INDICATORS
(Figure 2)
qREMOTE CONTROL BUS TERMINALS (REMOTE
CONT. BUS)
These terminals can used to connect other audio equipment that is equipped with a remote control bus terminal. Connection requires a special cable. The bus OUT terminal sends signal to the connected equipment, while the bus IN terminals receive signals.
wAUX1/AUX2 INPUT JACKS
These auxiliary input jacks can be used to connect the audio output of a TV multiplex/stereo audio tuner, VCR, laserdisc system, or other AV component audio output.
eTUNER INPUT JACKS
Connect these jacks to the output jacks of your tuner.
rCD INPUT JACKS
Connect these jacks to the output jacks of your compact disc player.
tPHONO INPUT JACKS
Connect these jacks to the output jacks of your turntable. These input jack are exclusive for a turntable equipped with MM (Moving Magnet) cartridge.
yTAPE,
Connect these jacks to the play (output) and record (input) jacks of
your recorders. Up to two decks can be connected.
uPROCESSOR IN/OUT JACKS
Use these jacks to connect a graphic equalizer or other analog audio processor. When not used, leave these jacks connected with the supplied connecting pins.
iGROUND TERMINAL
If your turntable has a grounding wire, connect it to this terminal.
oSPEAKER SYSTEMS
Connect your speaker system(s) to these terminals. There are two sets of terminals, so you can connect either one or two speaker systems.
!0 AC OUTLETS (SWITCHED)
Connect the power cord of another piece of equipment (VCR, tuner, CD) when you want the power of the connected equipment auto- matically turned on whenever you turn on this amplifier. For this to work correctly, the power switch of the connected equipment must be left on. Normally, the audio output of the connected equipment is also connected to this amplifier. Note that the total power con- sumption of the connected all equipment must not exceed 100W.
!1 POWER CORD
Connect the power cord to a standard household power outlet.
!2 POWER SWITCH
Press this switch to turn power on (depressed) and off (raised). Note that the power of any equipment connected to the switched AC out- let on the rear panel (see 10 above) is also turned on and off by operating this switch.
Turning on the power causes the POWER indicator to light, and the POWER indicator goes out when power is turned off.
While the POWER switch is in the ON position (depressed), you can put use the remote control unit’s SYSTEM POWER ON and OFF button to switch the amplifier between standby (indicated when the @6 STANDBY indicator is lit) and power on.
!3 CLASS A INDICATOR
This indicator lights when the amplifier is in the Class A operation mode. See “@3Class A Switch” for details.
!4
Press one of these switches to select a connected tape deck or
Pressing a
!5 INPUT SELECTOR
Use this selector to specify PHONO, CD, TUNER, AUX 1, or AUX 2 as the program source for recording or play. Selecting a program source causes the indicator above it to light.
Changing the INPUT SELECTOR setting while the amplifier is in the Standby Mode automatically turns power back on.
!6 REMOTE SENSOR
The remote sensor receive infrared commands from the remote con- trol unit. Note that the remote control unit must be pointed directly at the remote sensor for proper operation.
!7 VOLUME CONTROL
Rotate this knob clockwise to increase volume, and
!8 MUTING INDICATOR
This indicator lights when muting is activated by pressing the remote control unit’s MUTE button.
IMPORTANT:
Be sure to double check the VOLUME control setting before press ing the remote control unit’s MUTE button to cancel muting. Restoring audio output while the VOLUME control setting is too high can damage your speakers.
!9 BALANCE CONTROL
Rotate this knob to shift the balance of stereo output left and right. Note that turning the BALANCE control all the way in either direction causes output from the other side to be eliminated entirely.
@0 RECORD (REC) SELECTOR SWITCH
Use this switch to select recording between the tape deck and CD- R(MD) or recording of the signsl selected by the INPUT SELSCTOR SWITCH and out put from the REC OUT jacks.
See the note under “Tape Deck
@1 SOURCE DIRECT SWITCH
Press this switch to turn source direct on (depressed) and off (raised). When source direct is turned on, the audio signal path is as short and direct as possible in order to enjoy
NOTE:
Tape and
@2 BASS AND TREBLE TONE CONTROLS
Use these controls to control the levels of their corresponding fre- quency bands. TREBLE adjusts the high frequency band, while BASS adjusts the low frequency band. Rotating a control towards
(+)enhance the frequency band, while rotating towards
4
