3.Press “1” on the keyboard of the HomeGuard MS8000: one high tone is given to confirm.

4.Place the battery (9V) in the battery holder of the smoke detector. (Ensure that the polarity is correct.) The smoke alarm will send a radio signal to the base station: The LED on the sensor will illuminate briefly, and the base station will emit a short signal tone to confirm.

How to install the battery:

The smoke detector requires an alkaline battery

Match terminals on the end(s) of the battery with opposite terminal connectors on the detector. Be sure to insert the alkaline battery in the position shown on the detector.

When terminals are properly matched, push the battery firmly in place until it snaps and cannot be shaken loose.

5.Even if you are using more than one smoke detector you only have to register the first one.

6.Press any button on your HomeGuard MS8000 keyboard to finalize the registration procedure. One short low tone will be given and the green indicator stops flashing.

Now the smoke detector is registered and ready for use.

You can test your system by pressing the test key on the smoke detector for more than 2 seconds.

In the case of a fire the smoke detector sends the alarm signal to the Marmitek alarm installation (it does not matter whether the HomeGuard MS8000 is set to arm or disarm. The alarm will be triggered in both cases!).

Your HomeGuard MS8000 will dial the pre-programmed telephone numbers and its internal siren will sound (depending on your settings).

9 CHANGING THE ADDRESS OF THE SMOKE DETECTOR

The Marmitek SD10 supports different addresses for each sensor. You will need to use this feature when your neighbour also uses a Marmitek security system combined with one or more SD10 smoke detectors.

Changing the address of the sensor:

The default address of your sensor is 1. Every key-press of the test-key increases the address of the sensor by 1. This only works immediately after the power-connection between the sensor and its battery is established.

To change the address, press the test-key during the first 2 seconds after connecting the battery. Each time you change the address of the sensor you will have to register this sensor again in your Marmitek base station (please read the corresponding chapter in this user manual (chapter 6 or 7 depending on your Marmitek security system). The smoke detector has 250 different addresses.

SD10

7

Page 7
Image 7
Marmitek SD10 owner manual Changing the Address of the Smoke Detector, Changing the address of the sensor

SD10 specifications

The Marmitek SD10 is an innovative device designed to enhance home entertainment systems through seamless HDMI signal transmission over a long range. This product stands out for its ability to deliver high-definition video and audio with superior quality, making it a favorite among home theater enthusiasts.

One of the key features of the Marmitek SD10 is its ability to support resolutions up to 1080p. This high-definition capability ensures that users can enjoy their favorite movies, games, and television shows in stunning clarity. The device operates on the principle of HDMI over Ethernet, allowing for transmission distances of up to 50 meters, which is impressive compared to traditional HDMI cables that typically have a limited range.

In terms of technology, the Marmitek SD10 utilizes advanced signal compression methods to maintain audio and video integrity over long distances. This ensures that there is minimal lag or distortion, providing a smooth viewing experience without interruptions. The unit is also equipped with a built-in Ethernet switch, which allows users to connect additional devices without needing extra cables.

Another notable characteristic of the SD10 is its plug-and-play design, which makes installation straightforward and hassle-free. Users can simply connect their source device, such as a Blu-ray player or gaming console, to the transmitter, and then connect the receiver to their display, be it a TV or projector. This user-friendly aspect makes it an ideal choice even for those who may not be tech-savvy.

The Marmitek SD10 also features infrared (IR) remote control capabilities, enabling users to operate source devices from the receiver location. This adds an extra layer of convenience, as users can control their media playback without needing to be physically near the equipment.

Additionally, the device is designed to be compatible with various HDMI formats, including 3D video support, ensuring that it meets the demands of modern multimedia content. Its robust build quality and reliable performance make it a worthwhile investment for anyone looking to enhance their home entertainment experience.

In summary, the Marmitek SD10 is a powerful HDMI extender that combines high-definition video and audio transmission with user-friendly features and advanced technology, making it an essential component for modern home theaters.