Marshall Amplification MG50FX, MG100HFX, MG100FX manual MG15FX & MG30FX

Footcontroller (optional - PEDL-90008)
1. Footswitches		When either a Channel preset or Footswitch preset has	For all amplifiers, when entering Tuner mode the unit
Each footswitch can be assigned a different stored function.		been altered the Digital Display (3) will begin to flash.	mutes and Clean : Crunch (3) and OD (5) switches light
2. LED Status Panel		The footcontroller will flash the relevant number if a	yellow.
		Footswitch preset has been altered or will flash a “-“ if a	The Digital Display (3) indicates the closest current note
This always reflects the current status of the amplifier or tuner details:		Channel preset has been altered.
CLN & OD: Current Channel		Pressing only the Store switch at this point will overwrite	being played. The indicator dot on the lower right hand
			corner shows if the current closest note is #.
REV: Reverb On/Off		the altered Channel or Footswitch preset.	The LED Status Panel (2) is used to show how far away
FX: FX Section On / Off		To store an altered Channel preset to the
Ext FX: External FX Loop On/Off (MG50FX & MG100FX)			from the closest note the current note being played is.
Damp: Damping Mode (MG50FX & MG100FX)		Footswitch instead, hold the Store switch and while	When the central FX Status LED lights, it indicates the
Tap: Tap Tempo speed.		held down, press your chosen Footswitch (1) - Just like	correct tuning, with the others progressively indicating
3. Digital Display		a normal Preset Store.	the tuning is up to 50 cents up or down.
		To store an altered Footswitch Preset to another	To exit the Tuner push any footswitch, the amplifier will
This display indicates the various functions of the footcontroller.
		Footswitch hold the Store switch and while held down,	then exit returning to the settings before entering.
		press your chosen Footswitch (1) - Just like a normal
3	2	Preset Store.
		Digital Display
		When recalling a footswitch preset, the Digital Display
		(3) will indicate which footswitch number has been
		pressed.
		If a Channel preset has been recalled the Digital
		Display (3) will remain blank.
		When either a Channel preset or Footswitch preset has
		been altered the Digital Display (3) will begin to flash.
		The footswitch will flash the relevant number if a
		Footswitch preset has been altered or will flash a “-“ if a
		Channel preset has been altered.
		Tuner
		The Tuner can be accessed in two ways:
		MG15FX & MG30FX
		By simultaneously pushing the Tap (10) and Store (12)
		switches on the front panel or by assigning the Tuner to
		the footswitch. Note: On factory reset / first switch on,
		the Tuner is already assigned to Footswitch number 4.
		Assigning the Tuner to a footswitch is carried out like
		any other Switch Store. To assign the Tuner to the
		footswitch hold down the Tap (10) and Store (12)
1
		switches and press the chosen footswitch you wish to
		assign it to. The Digital Display (3) will swirl to show that
Footcontroller Factory Settings	The Digital Display (3) will swirl to show that the	the footswitch has been assigned. You can then release
		the footswitch and front panel switch.
Footswitch 1: Clean : Crunch Switch	footswitch has been assigned. You can then release the	MG50FX & MG100FX
Footswitch 2: Overdrive Switch	footswitch and front panel switch.	By simultaneously pushing the Damping (17) and Store
Footswitch 3: Tap Tempo Switch	Preset Store	(19) switches on the front panel or by assigning the
Footswitch 4: Tuner		Tuner to the footswitch. Note: On factory reset / first
Programming	To assign a preset to a Footswitch (1), select the	switch on, the Tuner is already assigned to Footswitch
	required channel and modify the front panel controls if
The footswitch can be programmed to store front panel	required, press and hold the Store switch on the front	number 4.
switches (Switch Store) or complete presets (Preset	panel and while held down, press your chosen	Assigning the Tuner to a footswitch is carried out like
Store).	Footswitch (1).	any other Switch Store. To assign the Tuner to the
Switch Store	The Digital Display (3) will swirl to show that the	footswitch hold down the Damping (17) and Store (19)
		switches and press the chosen footswitch you wish to
To assign a front panel switch to a Footswitch (1),	footswitch has been assigned. You can then release the	assign it to. The Digital Display (3) will swirl to show that
press and hold the front panel switch and while held	footswitch and Store switch.	the footswitch has been assigned. You can then release
down press the Footswitch (1) you wish to assign it to.	Footcontroller Presets are independent of the dedicated	the footswitch and front panel switch.
	Channel presets stored within the amplifier. This allows

you to create a number of presets based on the same channel/pre-amp setting.

ENGLISH

8 9