D I P A N D F L O W C O O L E R S U S E R ’ S M A N U A L
Introduction
Please read all the information in this booklet before using the unit.
Warning
HIGH TEMPERATURES ARE DANGEROUS: they can cause serious burns to operators and ignite combustible material.
Techne have taken great care in the design of these units to protect operators from hazards, but users should pay attention to the following points:
•USE CARE AND WEAR PROTECTIVE GLOVES TO PROTECT HANDS;
•DO NOT put hot objects on or near combustible objects;
•DO NOT operate the unit close to inflammable liquids or gases;
•DO NOT place any liquid directly in your unit;
•At all times USE COMMON SENSE.
Operator Safety
All users of Techne equipment must have available the relevant literature needed to ensure their safety.
It is important that only suitably trained personnel operate this equipment, in accordance with the instructions contained in this manual and with general safety standards and procedures. If the equipment is used in a manner not specified by Techne the protection provided by the equipment to the user may be impaired.
All Techne units have been designed to conform to international safety requirements and are fitted with an overtemperature cutout. On some models, the cutout is adjustable and should be set to suit the application. On all other models the cutout is preset to protect the unit.
If a safety problem should be encountered, switch off at the mains socket and remove the plug from the supply.
Installation
1.All Techne units are supplied with a power cable. This may be integral or
2.Before connecting the mains supply, check the voltage against the rating plate. Connect the mains cable to a suitable plug according to the table below. Note that the unit must be earthed to ensure proper electrical safety.
Connections | 220/240V | 110/120V |
Live | Brown | Black |
Neutral | Blue | White |
Earth | Green/yellow | Green |
The fused plug supplied with the mains lead for use in the UK is fitted with the following value fuse to protect the cable:
230V UK | 13 AMP |
The fuse in the unit protects the unit and the operator.
Note that units marked 230V on the rating plate work at 220V; units marked 120V work at 110V. In both cases, however, the heating rate will degrade by approximately 8%. The rating plate is on the rear of the unit.
3.Plug the mains cable into the socket on the rear of the unit.
4.Place the unit on a suitable bench or flat workspace, or in a fume cupboard if required, ensuring that the air inlet vents on the underside are free from obstruction.
5.Symbols on or near the power switch of the unit have the following meanings:
I: mains switch On
O : mains switch Off
After use
When you have finished heating samples, remember that parts of the unit – the tubes, blocks and associated accessories
– may be very hot. Take the precautions listed earlier.
Guarantee
The unit is guaranteed against any defect in material or workmanship for the period specified on the enclosed guarantee card. This period is from the date of purchase, and within this period all defective parts will be replaced free of charge provided that the defect is not the result of misuse, accident or negligence. Servicing under this guarantee should be obtained from the supplier.
Notwithstanding the description and specification(s) of the units contained in the Operator’s Manual, Techne hereby reserves the right to make such changes as it sees fit to the units or to any component of the units.
This Manual has been prepared solely for the convenience of Techne customers and nothing in this Instruction Book shall be taken as a warranty, condition or representation concerning the description, merchantability, fitness for purpose or otherwise of the units or components.
User maintenance
NOTE THAT THIS EQUIPMENT SHOULD ONLY BE DISMANTLED BY PROPERLY TRAINED PERSONNEL.
REMOVING THE SIDE, FRONT OR REAR PANELS EXPOSES POTENTIALLY LETHAL MAINS VOLTAGES.
THERE ARE NO USER MAINTAINABLE PARTS WITHIN THE EQUIPMENT.
In the unlikely event that you experience any problems with your unit which cannot easily be remedied, you should contact your supplier and return the unit if necessary. Please include any details of the fault observed and remember to return the unit in its original packing. Techne accept no responsibility for damage to units which are not properly packed for shipping: if in doubt, contact your supplier. See the Decontamination Certificate supplied with your unit.
1.Cleaning
Before cleaning your unit ALWAYS disconnect from the power supply and allow to cool below 50° C.
Your unit can be cleaned by wiping with a damp soapy cloth. Care should be exercised to prevent water from running inside the unit. Do not use abrasive cleaners.
2.Fuses
Your unit is protected by one or two fuses. These should only be changed by suitably qualified personnel.
If the fuses blow persistently, a serious fault is indicated and you may need to return the unit to your supplier for repair.
Contact Information
For technical, sales or servicing information, contact your local Techne dealer or,
Barloworld Scientific Ltd
Beacon Road, Stone
Staffordshire
ST15 0SA, United Kingdom
Telephone: | +44(0)1785 812121 |
Fax: | +44(0)1785 813748 |
or,
Techne Inc, 3 Terri Lane,
Suite 10, Burlington,
New Jersey 08016, USA.
Telephone: | |
Toll free: | |
Fax: | |
labproducts@techneusa.com | |
Web site: | www.techneusa.com |
P A G E 4
