OWNER’S MANUAL
GENERATOR
FEATURES
Continued
2. If the GFCI receptacle tests okay, re- |
store power by pushing the RESET |
button back in. The test lamp should |
work at this time. IMPORTANT: You |
must press the RESET button firmly |
and fully. It should lock into place. If |
the GFCI does not lock into place, do |
RECEPTACLE CIRCUIT BREAKER
The circuit breakers protect the receptacles and alternator. Overloading generator will trip circuit breaker. A short circuit in item being powered will also trip breaker. If this occurs, unplug electrical load from recep- tacle. Let circuit breaker cool down. Push circuit breaker button to reset.
Electric motors need higher starting current. They require up to
Oil
Oil Level
At Top Of
Filler Neck
Dipstick
not use receptacle. Contact a qualified |
electrician for repairs. |
RESET
TEST
Figure 4 - GFCI Receptacle
wattage to start. The starting current needed may be too high. This can cause nuisance circuit breaker tripping. To help prevent this, start electric motors first. Connect ad- ditional items to generator after starting motors. If this continues to happen, reduce the total generator load.
Normal 20 | Tripped 20 |
Figure 6 - Receptacle Circuit Breaker Button
Note: High ambient temperature will cause nuisance tripping.
Figure 7 - Checking Oil Level (Model MGH4000C Shown)
FUEL
WARNING: Gasoline presents a hazard of fire or explosion. Gasoline is flammable. Its vapor is explosive.
• | Keep fuel out of children’s |
| reach. |
• | Refuel generator in a well- |
| vented area. Do not fill fuel tank |
| in the dark. Do not refuel while |
| engine is running. Unhook all |
| electrical loads and shut off |
ENGINE CIRCUIT BREAKER
(Models MGH5000DIE, MGH6500IE, and MGH10000A)
This circuit breaker, or fuse, protects the battery charging circuit. A short circuit will trip the circuit breaker. The circuit breaker will also trip if you install battery wrong. Push circuit breaker button to reset. On Model MGH10000A, the fuse is located inside of the Keyswitch box.
| ON | |
| OFF START | |
Engine Circuit | ENGINE SW | |
CIRCUIT | ||
Breaker Button | ||
BREAKER | ||
| ON/push OFF |
Figure 5 - Engine Circuit Breaker
ENGINE OIL
We ship the generator without oil in the engine crankcase. You must add oil before starting engine. See engine owner’s manual for specific oil type.
CHECKING OIL LEVEL AND ADDING OIL
Follow steps below to check oil level. Make sure engine is level and stopped.
1.Remove dipstick (see Figure 7). Wipe dipstick clean.
2.Insert dipstick into oil filler neck. Do not screw it in. Oil level should be at top of filler neck. Oil should cover most of dipstick. For Model MGH10000A only, the oil should be between the two dots on dipstick.
3.If level is low, fill to top of oil filler neck (see Figure 7). For Model MGH10000A only, fill to top dot on dipstick. Only use oil recommended in engine owner’s manual.
Note: If oil level is too low, oil alert system will shutdown engine and prevent engine from restarting.
| engine before refueling. |
• | Do not overfill fuel tank. Al- |
| ways allow room for fuel to |
| expand. If you overfill tank, fuel |
| can overflow onto hot engine. |
| This can cause fire or explo- |
| sion. After refueling, tightly |
| close fuel tank cap. |
• | Do not spill fuel. Fuel or fuel |
| vapor may ignite. If fuel spills, |
| make sure area is dry before |
| starting engine. |
• Never smoke in refueling area. | |
| Never allow open flames or |
| sparks in area. |
• | Store fuel in approved con- |
| tainer. Store fuel in a well- |
| vented area free of open flames |
| or sparks. |
Use clean, fresh, unleaded gasoline. Use gasoline with octane rating of 86 or higher. Service station gasoline pumps should dis- play the octane rating. Using gasoline with lower octane level could damage engine. Avoid getting dirt, dust, or water in fuel tank. Do not mix oil with gasoline.
See engine owner’s manual for more information.
106813 | 7 |
